BHO with Vacuum oil/wax tutorial
- Thread starter Guzias1
- Start date
Guzias1
Well-Known Member
Goo fo life !!
It happens man. And it's extremely frustrating.
You pretty much still be such with that consistency. Is our purged enough? Does it crackle any under a flame?
If it's no crackle. Market it as some really dank taffy. Good luck!
You have pretty much mostly ruined consistency. But other than that. You got a good smelling, pretty taffy.
On to the next one I say! Don't dead on the post. Look towards the future! Be careful with them heats!
It happens man. And it's extremely frustrating.
You pretty much still be such with that consistency. Is our purged enough? Does it crackle any under a flame?
If it's no crackle. Market it as some really dank taffy. Good luck!
You have pretty much mostly ruined consistency. But other than that. You got a good smelling, pretty taffy.
On to the next one I say! Don't dead on the post. Look towards the future! Be careful with them heats!
Ya man no worries. I'm a believer that we learn the most by our own mistakes. Yes It was purged a long time and it went past shatter state, no bubbles etc. So it should burn nice and clean.
I'll keep it as personal. I put it in the freezer and it's solid hard so I'll keep it like that and when I want a hit just snap a chunk off.
I should have went with my gut instinct and pulled it out as soon as the surface was nice and firm.
All of my batches have waxed up between 115-130 but most at the 120F range.
Soooooo me's a ordering a vac oven!
I figure I'll keep a couple chambers going to do all initial purging; then when I get it to a slow bubbling state move the batches to the oven to finish them off. at a nice even temp.
Having the chamber on the griddle for the final wax up is a little touch and go..If I gotta go out for a few hours or sleep etc..the chamber likes to slowly creep up in temp.
Gotta play it on the safe side and turn it down while I go out and sleep from now on till I get the vac oven.
I'll keep it as personal. I put it in the freezer and it's solid hard so I'll keep it like that and when I want a hit just snap a chunk off.
I should have went with my gut instinct and pulled it out as soon as the surface was nice and firm.
All of my batches have waxed up between 115-130 but most at the 120F range.
Soooooo me's a ordering a vac oven!
I figure I'll keep a couple chambers going to do all initial purging; then when I get it to a slow bubbling state move the batches to the oven to finish them off. at a nice even temp.
Having the chamber on the griddle for the final wax up is a little touch and go..If I gotta go out for a few hours or sleep etc..the chamber likes to slowly creep up in temp.
Gotta play it on the safe side and turn it down while I go out and sleep from now on till I get the vac oven.
garlictrain
Well-Known Member
Hey everyone!
I was pointed this direction by SirDabs and fuck do you guys got skills! I've done about 15 bho runs over the last year, always heat matting, finally getting into vac purge and winterizing my extracts!
My BHO backround started in 2006 when I was living in norcal around the hills of coastal mendo helping my girls uncle blast trim for the farms. This was by far the sketchiest BHO setup I'd ever run but I had no fucking CLUE! Not to mention how harsh the shit was I WISH I knew about dewaxxin...
Also we were running a 2in 4 ft long piece of pvc with a 3/4 ball valve at the bottom to "regulate" flow! We blasted directly onto glass doors and after a day in the sun got out the paint chipper and made our 50%!!! Never again lol!!!
I've been reading on this thread from page 1 to page 105 over the last few days and I'm jumping ahead just to show a little of my newer tweaked process based on so many of the contributions of this very thread, as well as the concentrate section of RIU!
Mad props to everyone for sharing the knowledge!
A basic run down of my process:
1. Usually my source flower/trim is decarbed so I throw the cans of tane as well as the trim/flowers into the freezer over night.
2. I pack the tubes the following day (ancient Chinese secret) and throw them back into the freezer while I set up the BHO station (table outdoors with wood sheet over the top).
3. Welders gloves check, safety goggles check, I like to blast 4 x 100g tubes at a time, 2 cans each... Picked up the tubes blown by buddy who is wax master for a MIP an follow his tech pretty closely. It's highly regarded by him and he's gotten one of the highest unbiased thc% in the CO industry as of yet!!!
4. Each tube is blown into its own 6 cup pyrex dish for individual purging, even like on this last run I used all Bubblegum but still did separate pyrex so as to control the purge even more. Once stopped purging at room temp I whipped the shit and scraped it up to throw on parchment and freeze to rework.
After the freezer, before the winterizing...
4 x 100g tubes came out to 48g frozen not yet fully purged Bubblegum YUMM!!!
5. Ok I had to rewarm the frozen false shatter in order to mix in the 190 everclear... nice and SLOW....
Prefroze my filter and glass for a few hrs before beginning filtration. Would pour some, stick back in the freezer, pour some more....
Once all is poured into the filter I recovered with foil and stuck back in freezer overnight...
6. This morning I pulled out the soon to be winterized meds and CHECK IT OUT!
My filter is FULL O WAX!!! Ouch no wonder my lungs been aching!
Is this finally the holy grail for non lung piercing oil rips?!!! Hope so
7. Pour nice and slow.... According to my wax master friend it is near impossible to wax decarbed meds... Don't really care myself I just need a clean product that I don't gotta rip 5x to get where I need to be
I KNOW you guys KNOW WTF I'm talking bout!!!!
8. This is where I'm at currently. A nice low temp heat pad OUTSIDE purging the vapors...
OK now I'm back to page 105 of this thread and will hopefully be caught up in a day or so!
Happy Dabbing
I was pointed this direction by SirDabs and fuck do you guys got skills! I've done about 15 bho runs over the last year, always heat matting, finally getting into vac purge and winterizing my extracts!
My BHO backround started in 2006 when I was living in norcal around the hills of coastal mendo helping my girls uncle blast trim for the farms. This was by far the sketchiest BHO setup I'd ever run but I had no fucking CLUE! Not to mention how harsh the shit was I WISH I knew about dewaxxin...
Also we were running a 2in 4 ft long piece of pvc with a 3/4 ball valve at the bottom to "regulate" flow! We blasted directly onto glass doors and after a day in the sun got out the paint chipper and made our 50%!!! Never again lol!!!
I've been reading on this thread from page 1 to page 105 over the last few days and I'm jumping ahead just to show a little of my newer tweaked process based on so many of the contributions of this very thread, as well as the concentrate section of RIU!
Mad props to everyone for sharing the knowledge!
A basic run down of my process:
1. Usually my source flower/trim is decarbed so I throw the cans of tane as well as the trim/flowers into the freezer over night.
2. I pack the tubes the following day (ancient Chinese secret) and throw them back into the freezer while I set up the BHO station (table outdoors with wood sheet over the top).
3. Welders gloves check, safety goggles check, I like to blast 4 x 100g tubes at a time, 2 cans each... Picked up the tubes blown by buddy who is wax master for a MIP an follow his tech pretty closely. It's highly regarded by him and he's gotten one of the highest unbiased thc% in the CO industry as of yet!!!
4. Each tube is blown into its own 6 cup pyrex dish for individual purging, even like on this last run I used all Bubblegum but still did separate pyrex so as to control the purge even more. Once stopped purging at room temp I whipped the shit and scraped it up to throw on parchment and freeze to rework.
After the freezer, before the winterizing...
4 x 100g tubes came out to 48g frozen not yet fully purged Bubblegum YUMM!!!
5. Ok I had to rewarm the frozen false shatter in order to mix in the 190 everclear... nice and SLOW....
Prefroze my filter and glass for a few hrs before beginning filtration. Would pour some, stick back in the freezer, pour some more....
Once all is poured into the filter I recovered with foil and stuck back in freezer overnight...
6. This morning I pulled out the soon to be winterized meds and CHECK IT OUT!
My filter is FULL O WAX!!! Ouch no wonder my lungs been aching!
Is this finally the holy grail for non lung piercing oil rips?!!! Hope so
7. Pour nice and slow.... According to my wax master friend it is near impossible to wax decarbed meds... Don't really care myself I just need a clean product that I don't gotta rip 5x to get where I need to be
I KNOW you guys KNOW WTF I'm talking bout!!!!
8. This is where I'm at currently. A nice low temp heat pad OUTSIDE purging the vapors...
OK now I'm back to page 105 of this thread and will hopefully be caught up in a day or so!
Happy Dabbing
Guzias1
Well-Known Member
Helll yaaa man. I heard about them mendo peeps doing some crazy blasting.
Glass doors was the most memorable one. Heard some would load up air tanks along with butane some how, and blast away onto the sheets. Scrape once ready... simple! But mehhhh
Ive been enjoying the likes. Looks like you just about pat the half way point on the thread
Man. I gotta say. You got it. You almost done! Just let that pan sit out. Make sure debris don't contaminate it.
Ever clear evaps really well. Way better than iso 99 .
I think it's ready enough once you touch it, and it don't stick. ( you be the judge though!)
Hope to see results soon!!
And enjoyyyyu. Properly winterized is amazingly smooth. Especially compared to some over wax filled bho.
Enjoy!!
Glass doors was the most memorable one. Heard some would load up air tanks along with butane some how, and blast away onto the sheets. Scrape once ready... simple! But mehhhh
Ive been enjoying the likes. Looks like you just about pat the half way point on the thread
Man. I gotta say. You got it. You almost done! Just let that pan sit out. Make sure debris don't contaminate it.
Ever clear evaps really well. Way better than iso 99 .
I think it's ready enough once you touch it, and it don't stick. ( you be the judge though!)
Hope to see results soon!!
And enjoyyyyu. Properly winterized is amazingly smooth. Especially compared to some over wax filled bho.
Enjoy!!
Guzias1
Well-Known Member
Oooo. I also rec you get a fan blowing lightly over the Pyrex. And make sure the surface of the oil isn't above 88f 
Qwizo Will say no heat. Ooooo. But I say low heat, and fan Will make it come out much quicker. Check on it every few hours or so
Glad to have you on board.
Bc!!! Please get that oven. I want to see it work. See if it's with it
Need your trial error, and reviews..thanks
Qwizo Will say no heat. Ooooo. But I say low heat, and fan Will make it come out much quicker. Check on it every few hours or so
Glad to have you on board.
Bc!!! Please get that oven. I want to see it work. See if it's with it
Need your trial error, and reviews..thanks
SaybianTv
Active Member
dayumm. so your small fattys, hold roughly the same as my skinnys... i bet thats a work out though :]
got late, but still wanted to try out the new ish. sooo, today, i packed about 200 grams of ground buds per tube, and came up about a half oz, - oz short per tube, so i threw a similar re run to fill it in.. soooo roughly 215 this time per tube 430 total. :] almostttttttt a lb!! i could probably push it.. but i dunno, hopefully when it comes time to unpack them tehy aint toooo tough.
my tube is 5 bottles long :]
custom fab
frozennnn tubes (did them one at a time, {first time trying this double tube stand setup!} worked like a champpp)
dissolved and stirred for a few minutes in warm everclear, andd into the freezer she wenttt
looking gooood
here is pic of room temp bho yeeeeeeee
double timmeee, yesssss. and i made a mount for my tubes right by the outsidesss :]
3 cans per tube. 6 total
took 3.5 minutes for first two cans. they fill her up prettty good.
let the last can just sprayyyyyyy through,
SFV OG. hopefully it comes out good,
leaving the tubes up to dry, gonna reblast in morning, also winterize that, and compare!!!!!
My god man who the hell do you think you are climbing a space ladder to get onto that tube just to blast from the moon into a pan back on earth.
Guzias1
Well-Known Member
Lolll. Luckily they are just short enough
Guzias1
Well-Known Member
lollllllllll, skyladder, thanks! ok, ya, we'll RIU T.M. that, "The Skyladder" and its fleet :]
how about a missile silo for my setup ?
vac assisted pour though is pretty sweet though..been thinking about that ish..
how do you go about doing that? please expain im thinking>>>
vacuum > closed off valve to big empty vacuum chamber (full of vacuum)> valve >> assisted pour chamber >> tube?
you could draw a picture if thats easier :]
how about a missile silo for my setup ?
vac assisted pour though is pretty sweet though..been thinking about that ish..
how do you go about doing that? please expain im thinking>>>
vacuum > closed off valve to big empty vacuum chamber (full of vacuum)> valve >> assisted pour chamber >> tube?
you could draw a picture if thats easier :]
I noticed on the everclear bottles it's grain alcohol. What stops people [normal ones that is] from drinking it?
We've got methylated spirit here. 95% v/v ethanol the 5% of Idk what, is a stinky additive/s to stop people from putting it in the punch.
I assume the 5% of stinky shit precludes metho as a satisfactory solvent?
We've got methylated spirit here. 95% v/v ethanol the 5% of Idk what, is a stinky additive/s to stop people from putting it in the punch.
I assume the 5% of stinky shit precludes metho as a satisfactory solvent?
qwizoking
Well-Known Member
"methylated spirits". Other typical additives include methanol, isopropyl alcohol, acetone, methyl ethyl ketone, methyl isobutyl ketone, and denatonium.
denatonium is often added to give the substance an extremely bitter flavor. Substances such as pyridine help to give the mixture an unpleasant odor, and emetic (vomiting) agents such as syrup of ipecac may also be included."
Soooo if you think your up to the task of removing any of the above....
You can drink ever clear but it is fairly irritating...
denatonium is often added to give the substance an extremely bitter flavor. Substances such as pyridine help to give the mixture an unpleasant odor, and emetic (vomiting) agents such as syrup of ipecac may also be included."
Soooo if you think your up to the task of removing any of the above....
You can drink ever clear but it is fairly irritating...
Bublonichronic
Well-Known Member
Everclear dosent last long at my house, shit always ends up getting drank, gives a much better buzz than other stuff IMO, almost feels psycadelic opposed to just drunk blurryness, does a number on the stomach tho
qwizoking
Well-Known Member
When I was younger I was sent to some sort of alcohol awareness type class .they told everyone of a kid that was dared to take how ever many(I forgot now) shots of ever clear..supposedly passes out and falls in his puke. Had burns all over his esophagus and face etc...
They told that story forever so I never knew if it was true.... but I didn't drink again till college
They told that story forever so I never knew if it was true.... but I didn't drink again till college
Bublonichronic
Well-Known Member
Yea, you gotta mix it with somthin(I use orange juice) and not drink on a empty stomach...
Bublonichronic
Well-Known Member
Right, green dragon what? I make ever amberI mix it with my hash oil and drink it occasionally
.