Hey ray, with the gh nutes start at about 500 ppm and go from there.hey nice crop man...awesome...hey man im planing to put my clones to vege tomorrow into my dwc reservoir...how much nutes do you think i should start with? thanks ///GH nutes
Ok im goin in with a buddy on some seeds, he told me to figure out what kinds to get and where to get them... From what ive read on here, attitude seed is reliable, any suggestions on what what strains to get....
Yea attitude it is, how did you pay for them wannabee?attitude - they are reliable and stealth = ordered twice, no problems.
its nice to see how different strains do, so you could pick some you don't see a lot of or you could pick more autoflowering. Feminized are definitely the way to go.Sensi Seeds Northern Lights #5 X Haze, just looked this up and 150 for one seed, dam, thats seems like alot, but you do get a bunch of other free ones though. Should i get only feminized seeds or some of each?
I was going to do the LR2 with my hempstar mothers too but wasn't sure how the 24 hour light would work. but i did hear it will work. let me know how well it works or do you vedge 18/6. i vedge 24/7. I guess i could have kept the mothers and vedged them 18/6 with the LR2 but they were grown 24 and i thought it might flower them slowly. definately let me know. good luck
I had written more on the nute thing but lost it this morning when I had to refresh the page. But, Start them at about 500 ppm. And if you want to try to fine tune it kinda check your ppm daily. And it is best to know how much water is in your res so you can check it and see how much water they are using daily also. When your water goes down and your ppm goes down too, you need more nutes. If your water goes down and your ppm goes up you have to many nutes. And if it stay pretty close to the same your mix should be good. The GH nutes are pretty strong. The mild growth mix with only the 3 parts shows 741 ppm. You can just mix that or add other stuff too. I've found the best way for me is to just mix up what I want to be in my solution, base nutes, and extras. And don't really worry about ppm at first. Then when I am done I check the ppm and ph. Adjust the ph if needed. Then just cut it with plain water to get the ppm I want. With the larger res I just mix in the container. But check as I'm adding the nutes and try not to go over. I try to start a little low with water level so if I go over to much I can add a little plain water. You can always just take some out if it is to strong and replace with plain. Hope that all made sense.thanks hashlover
Sweet Hashlover ...really good explanation...im going to follow this post...im excited...I had written more on the nute thing but lost it this morning when I had to refresh the page. But, Start them at about 500 ppm. And if you want to try to fine tune it kinda check your ppm daily. And it is best to know how much water is in your res so you can check it and see how much water they are using daily also. When your water goes down and your ppm goes down too, you need more nutes. If your water goes down and your ppm goes up you have to many nutes. And if it stay pretty close to the same your mix should be good. The GH nutes are pretty strong. The mild growth mix with only the 3 parts shows 741 ppm. You can just mix that or add other stuff too. I've found the best way for me is to just mix up what I want to be in my solution, base nutes, and extras. And don't really worry about ppm at first. Then when I am done I check the ppm and ph. Adjust the ph if needed. Then just cut it with plain water to get the ppm I want. With the larger res I just mix in the container. But check as I'm adding the nutes and try not to go over. I try to start a little low with water level so if I go over to much I can add a little plain water. You can always just take some out if it is to strong and replace with plain. Hope that all made sense.