What ud diodes did you use?Using the Blackdog shell, I mounted four 140 mm pin fins with 35 emitters each. Three engines with Osram Oslon 80's mostly in 5700k but a few 660nm and even less 450nm which are being driven with a Meanwell HLG-185H-700A (Drove 17 but I dropped it down to 15 for obvious reasons) and the other using one of the cheap blackdog driver at 900 ma power was only able to drive the weaker 660nm with a punch. Sill working on this but almost there, I need thermal adhesive because I bought the wrong shit last time and also need to finish securing the heatsinks with a couple bars and finishing wiring it. Too bad I got into this light shit after wasting a couple G's on hogwash.
View attachment 3918143
For the bigger build I used an aluminum door frame from the 70's (works like a charm my friends but I imagine windows as well). I gutted the Blackdog and separated the two PCBs and heatsinks with CXB-3590s in between. I also took out their emitters in white, IR and UV as well as green. I think 5 of the 6 UV diodes were dead or became dead after the extra heat I hit them with. Ill post some pictures of that a different day. Driving the 3590's at 2100ma so its cranking the white but I probably screwed that up.
Sorry, I meant UV diodesOn these two drivers I used the Oslons with a 80 degree beam angle lens
5700k White mostly
http://www.mouser.com/ProductDetail/OSRAM-Opto-Semiconductors/GW-CS8PM1PM-LRLT-XX52-1/?qs=sGAEpiMZZMu4Prknbu83y9/0l5xAqdxo4%2boCOjIRN6Kc2ldQyfnLdw==
I also used the same ones in deep blue and their 660 red
Cree has released a new bin for their XP-G3 royal blues.new XP-g3?
5630 pcb sourceDo you know if they can make custom PCBs for 5630 (or other) sized leds?
They aren't in their normal inventory but I see they have a subscription service.
Otherwise I'll just wait for the new xp-g3s
560mm or 1120 mm single rowHey guys
Just got some LM561C S 6 bins in and looking to build custom boards to suit, what sort of board should I build?
Cheers
Mark
lol560mm or 1120 mm single row
Are you doing custom orders? I'm after 200 boards or strips. PM meHey guys
Just got some LM561C S 6 bins in and looking to build custom boards to suit, what sort of board should I build?
Cheers
Mark
Can you build a larger board for these Oslons or XPG3 in strips or rectangle strip 2x20?? 1x40???Hey guys
Just got some LM561C S 6 bins in and looking to build custom boards to suit, what sort of board should I build?
Cheers
Mark
do you prefer single over strip over an array like QB type boards?560mm or 1120 mm single row
Yes thats what Im considering, looking for ideas, I will PM you, Im thinking maybe 2 colours and then 660nm as well?Are you doing custom orders? I'm after 200 boards or strips. PM me
certainly can, what dimensions are you thinking?Can you build a larger board for these Oslons or XPG3 in strips or rectangle strip 2x20?? 1x40???
actually i'm looking for max dispersion, a large rectangular pcb would do, preferably at least twice the size of qb's.do you prefer single over strip over an array like QB type boards?
Cheers
Mark
I personally would be very interested in seeing how many Oslons you can get on a 140 mm mcpcb round (to fit the 140mm pin fin heatsinks with the contacts near the outer edges? I also would really like to use a larger board (maybe 12 inch by 6 inch) and how many Oslons could fit.certainly can, what dimensions are you thinking?
Cheers
Mark
based on 3 watts per chip 25 would be around 75 watts, you probably would not want much moreI personally would be very interested in seeing how many Oslons you can get on a 140 mm mcpcb round (to fit the 140mm pin fin heatsinks with the contacts near the outer edges? I also would really like to use a larger board (maybe 12 inch by 6 inch) and how many Oslons could fit.