Bridgelux EB-series on a 2' x 4' SCROG
- Thread starter graying.geek
- Start date
graying.geek
Well-Known Member
CRI and CCT being equal, the power input/output, and subsequently, lumens, scale as a direct proportion to the various strip lengths. (48 x 280 mm) = (24 x 560 mm) = (12 x 1120 mm).coolnow... just gotta decide on drivers....
and... if i get the 560mm strips, they will run at about 22v right...? will i still get close to 50w/sqft running less voltage than the big strips? (basically i want 2, 2x3 fixtures with 10-12 strips each so it can be broken into 2 for transport)
Last edited:
Danielson999
Well-Known Member
Using the 560mm strips does allow you to fill certain drivers better than 1120mm. Where you can fit 6 x 1120mm strips on one driver you can fit 13 of the 560mm so I guess you can squeeze a bit more power out using the 560mm. You'll just need to order 26 of them. For instance the 320H-C1050 driver has 305v, 13 x 560mm = 299v whereas the 1120mm strip fits 6 at 276v, not enough for 7 strips. So you squeeze an extra 25w out of the driver using 560mm.
klx
Well-Known Member
Yeah it was only one corner of one strip that had come away, but better safe than sorry.
Otherwise, after 1 week, my mums and veg plants are enjoying themselves under the 4000k rays
klx
Well-Known Member
Here are the mums and kids enjoying their new lights. The mum light is dimmed to 50% and the veg light is cranked to full to see what it can do. I use a 400W HPS in here in in winter so if it can come close to the veg performance of that then I will be happy. So far so good.
So my veg light is being upgraded to get better coverage in my veg tent (80x80x160cm) ... Making up this 60cm x 60cm frame to have another 4 strips... So thats 8 strips total @700ma for my veg tent 
@graying.geek how did you measure out your spread? im useless at maths lol I want to set them up a bit more to the outside to get that even spread
@graying.geek how did you measure out your spread? im useless at maths lol I want to set them up a bit more to the outside to get that even spread
graying.geek
Well-Known Member
In attempt to be precise, I calc'd it using the log of the number of strips to increase the spacing toward the middle, *but*, I would have done just as well by wagging it, as you, and others have done. That said, your middle space seems a bit wide but you certainly have the right idea. Ideally you could lay out the strips in whatever pattern you end up with, light them up, then check for even spread with a free LUX app. Re-position the strips, and check again.
hard to explain.... strips turn up tuesday so should have a pic up tues night
rayuki
Well-Known Member
cool look forward to it, im thinking of just mounting mine remotely but i do like having it all in one unit.hard to explain.... strips turn up tuesday so should have a pic up tues night
InTheValley
Well-Known Member
Bro, the light on the left is concaved?
rayuki
Well-Known Member
Lol yes it has a slight bend cause of the thin aluminium. Not a big deal just yet but it will be fixed at some point.
InTheValley
Well-Known Member
I thought so. You know, Id leave it like that, lol..
Ive sat and thought about doing just that.
Danielson999
Well-Known Member
I vote to not leave it like that. It will be visually upsetting to many people.
Chip Green
Well-Known Member
One of my 2x2 panels (11 EB 560s, 700ma MW ELG 240) has a slight concave flex, due to thin aluminum framing, and roll stock backing. I justified leaving it that way as, a means to distribute photons from the center strips for balance, as I had not been educated on unequal spacing as of the build day. LOL
InTheValley
Well-Known Member
working out for ya?
InTheValley
Well-Known Member
lol,