Frank Nitty
Well-Known Member
Tiiiimmmmberrrrrrr!!!
DIY with Quantum Boards
- Thread starter robincnn
- Start date
Budzbuddha
Well-Known Member
Wookie Wonder update ....
Week 4 of flower ...
Plus this a pollen chuck on a couple of lowers 2 weeks ago and we got some new seeds !
First she is doing well in the hempy buckets ....
Same GH NUTES ( MAXIBLOOM ) and kelp at straight water ( between feeds )
PH @5.9
Quantums 3500k 4 panel with Citizen Cobs
Power dim set at 360w ( 60w PER all QB and CoBs )
630-660nm supplemental boost
Smells like Sweet Earth ....
Pollenation was from that Sugar High ( GG4 X NINJA TURTLES ) plant that went full male . I harvested the sacks and pollinated the Wookie ( 2 lower branches ) .
.... You ARE the Father !
*************************************************************************************
And here is the new breeding : seeds are forming
Wookie Wonder x Sugar High
Week 4 of flower ...
Plus this a pollen chuck on a couple of lowers 2 weeks ago and we got some new seeds !
First she is doing well in the hempy buckets ....
Same GH NUTES ( MAXIBLOOM ) and kelp at straight water ( between feeds )
PH @5.9
Quantums 3500k 4 panel with Citizen Cobs
Power dim set at 360w ( 60w PER all QB and CoBs )
630-660nm supplemental boost
Smells like Sweet Earth ....
Pollenation was from that Sugar High ( GG4 X NINJA TURTLES ) plant that went full male . I harvested the sacks and pollinated the Wookie ( 2 lower branches ) .
.... You ARE the Father !*************************************************************************************
And here is the new breeding : seeds are forming
Wookie Wonder x Sugar High
PrometheanLeaf
Well-Known Member
@Stephenj37826 if I wanted to hang a single elite, what would be the best way?
Stephenj37826
Well-Known Member
You can find m4 eyebolts. Then a small hanger kit would work. We are looking into it now too include in the future. Hopefully next week they will be on the way.
uxcell 5 Pcs M4x11mm Thread 11mm Inside Dia 19mm Outside Dia 304 Stainless Steel Lifting Eye Bolt https://www.amazon.com/dp/B077GYM56Y/ref=cm_sw_r_cp_apa_i_IcU0Bb7HKJEM5
NanoGadget
Well-Known Member
Sup y'all. So i have an adorable little 2x3 space. There is currently 135w QB 288 kit in there and it did a marvelous job for me last run. However.. i was really only utilizing 2x2 or so of my space. I was thinking of adding a bit of light. Trying to decide between getting the bigger slate and adding nother 288 and running it at lower power or just grabbing a QB96 elite and using that to fill in the space. Either way i feel like I'm going to be under driving whichever i choose. The bigger slate/driver/second 288 otption gives me a light that can be run harder in a bigger space should i need it but is a bigger investment. What do you good folks think?
Humple
Well-Known Member
If I were you, I'd get the 288. But I'm a bit OCD about symmetry.
pop22
Well-Known Member
No the 324 is a 100+ volt board and the 288 is a 50 volt board. Boards must match fairly closely in voltage, even within the same board. That's why its best to buy the number of boards you want to run in total, all at once as they'll voltage match them.
That applies for parallel strings of boards, yes. Any build including a 100V board is going to run in series with a CC driver.
Budzbuddha
Well-Known Member
Lookin good ... had to google that one .
Never seen it. But sounds like a nice one.
3 way cross ... i like mazar but looks like a killer combo .... definitely keep us posted especially if it throws that blue bud pheno.
Now you just made me want to go bean shopping again *sighs *
Budzbuddha
Well-Known Member
Are you still running the Blue Dragons cuz unfortunately for me they didnt pan out ... they germed then kinda quit.
Oh well. Still have some left and may try again.
Oh well. Still have some left and may try again.
NanoGadget
Well-Known Member
I normally prefer symmetry as well, but I've been wanting to give a bit of that far red goodness a try and it's making the 96 very appealing. Lol.
Humple
Well-Known Member
Far red, you say?
https://www.instagram.com/p/BpGBI-bFYWB/?utm_source=ig_share_sheet&igshid=1xvd6f605kunc
Hopefully @Stephenj37826 or @robincnn will post a thread for this product. I've been thinking about adding some far red myself, and the small size of these strips makes them ideal for fitting into non-standard sized grow spaces.
NanoGadget
Well-Known Member
That too! But i misspoke. I was actually referring to deep red rather than far red. The 660nm on the 96 is what i was thinking of.
Humple
Well-Known Member
Ahh... Yeah, I've also been looking at the QB11 in 660nm. If I read HLG's site correctly (it can be a bit unclear on some things), it's two strips for $50.
pop22
Well-Known Member
Grew a couple in my greenhouse this summer. I always have some to vape, its may favorite. I had one tube of seed that was bad, I don't know why. I've sampled other tubes and they germ fine. Let me know, I'm sure more could find their way to you...
Budzbuddha
Well-Known Member
Sounds good ... I unfortunately have more beans than I could possibly run ...
However , I’m sure trading spaces “ could happen “ ....lol. If you looked at my latest cross ...
Host mom is hella stout and strong so these should be something.
Always liked the variety of cuts you run ... I’m the same way .... I gotta try this and that.
Plus I’m generating a SHIT LIST of beans to AVOID. Like Tangerine Dream .... horrible .
Barney’s Blue Cheese .... hot garbage too. Kind of why I brew my own.
Frank Nitty
Well-Known Member
Get another qb288...
Frank Nitty
Well-Known Member
Autopot Pop!!! You are the man!!! Wait!!! I've got it!!! Autopop22!!!