Cutter Electronics: Complete DIY COB kits

[welight]

when your looking for the stuff don't do 12 inch tiny pieces, do a longer bar that can span the entire middle of the standard 3 or 4 foot area

what spacing would you have leds on?
Cheers
Mark

 

[sinnamon]

when your looking for the stuff don't do 12 inch tiny pieces, do a longer bar that can span the entire middle of the standard 3 or 4 foot area

or more like 60 cm

 

[nl5xsk1]

I got 2 of the mau5 4 cobb kits that I'll be using to make 1 fixture

That's what I did, and things are looking promising

 

[Humble grower]

So can I run 2 LGSU 1400D drivers on 1 of the cutter 1-10v dimmer switches

 

[Humble grower]

View attachment 3687175 That's what I did, and things are looking promising

Looks good what size space are you using that for

 

[nl5xsk1]

Looks good what size space are you using that for

42"X42"

 

[anomolies]

View attachment 3687175 That's what I did, and things are looking promising

how come you didn't get the mau5- 8 kit? uses only 1 driver

 

[anomolies]

hey Mark, know you're probably super busy but wanted to remind you about the stella reflectors if you got them in by any chance? wanted to place my order before you run out of the unpainted heatsinks those look sweet

 

[Airwalker16]

So can I run 2 LGSU 1400D drivers on 1 of the cutter 1-10v dimmer switches

Why didn't you get the mau5-8 cob kit with just 1 driver? :/

 

[Humble grower]

42"X42"

Good stuff

Why didn't you get the mau5-8 cob kit with just 1 driver? :/

I will be for my next order this one I kinda jumped the gun and just ordered I may even order the bigger driver and keep the smaller ones for back up but until then I'm just going to work with what I have

 

[anomolies]

Good stuff

I will be for my next order this one I kinda jumped the gun and just ordered I may even order the bigger driver and keep the smaller ones for back up but until then I'm just going to work with what I have

what's the junction box for? was wondering if i'd need one with just a single driver.. don't really have that many wires

 

[nogod_]

Just a tidy place to keep all your connections out of harms way.

See: props for convincing your partner that you wont burn the house down.
See: great for soothing rampant OCD.

Also the twist-to-tighten fittings they come with are great for taking tension off of your connections.

Robins is beautiful but im cheap so i bought mine on sale from home despot for $1.94

what's the junction box for? was wondering if i'd need one with just a single driver.. don't really have that many wires

 

[Airwalker16]

what's the junction box for? was wondering if i'd need one with just a single driver.. don't really have that many wires

Just keeps stuff clean and gives you a place to house all your soldered/ clipped connections.

 

[ShyGuru]

@welight Mark I have a question about ordering from your site. I'm from the USA and created an account in order to purchase your pin fin heatsinks but the problem is the price is not reflected in USD. I went as far as possible before needing to enter a credit card number to continue and correctly checked each box saying I'm from the US but the price never changed. At which point in the billing process is the price supposed to convert? Any advice on how I should proceed? I'd like to order as soon as possible. Your assistance is greatly appreciated and my apologies if this isn't the correct place to post this question.

 

[Atulip]

@ ShyGuru Your bank will change it, and may charge a small fee for currency exchange.

 

[welight]

@welight Mark I have a question about ordering from your site. I'm from the USA and created an account in order to purchase your pin fin heatsinks but the problem is the price is not reflected in USD. I went as far as possible before needing to enter a credit card number to continue and correctly checked each box saying I'm from the US but the price never changed. At which point in the billing process is the price supposed to convert? Any advice on how I should proceed? I'd like to order as soon as possible. Your assistance is greatly appreciated and my apologies if this isn't the correct place to post this question.

not a problem, Atulip response above is correct, base currency is AUD, but whatever country your in, this will be converted to local currency when you pay
Cheers
Mark

 

[nl5xsk1]

how come you didn't get the mau5- 8 kit? uses only 1 driver

I actually picked up a couple extra cobs, the cutter drivers can run 5 cobs each, so if I want to add these , i can

 

[flaxseedoil1000]

@welight Mark I have a question about ordering from your site. I'm from the USA and created an account in order to purchase your pin fin heatsinks but the problem is the price is not reflected in USD. I went as far as possible before needing to enter a credit card number to continue and correctly checked each box saying I'm from the US but the price never changed. At which point in the billing process is the price supposed to convert? Any advice on how I should proceed? I'd like to order as soon as possible. Your assistance is greatly appreciated and my apologies if this isn't the correct place to post this question.

https://www.rollitup.org/t/cutter-electronics-complete-diy-cob-kits.902453/page-37#post-12585775

 

[Humble grower]

Victory is mine all that's left is put the dimmer switch in and hang it up! Not bad for my first build considering I have no electronic background at all. huge thanks for all the help couldn't have done it without it

 

[Airwalker16]

Victory is mine all that's left is put the dimmer switch in and hang it up! Not bad for my first build considering I have no electronic background at all. huge thanks for all the help couldn't have done it without it

Way cool. Looks like mine.... kinda. I spaced my 2 rows further apart though