Who has 3d printed things for your weed hobby? Include links to things if possible.

anexgrower · Jan 22, 2021

For your grow tent, or a herb grinder, or a bong?
I'll include my collection of things I may want to print in the near future:

Grow Tent Accessories by dalelovelace

Accessories I have made for my Apollo 2x4 grow tent. The poles on the Apollo are 0.65" so these should work with any tent that has 0.65" poles.Link to my grow tent:https://amzn.to/30TKHOsAlso included are intake grates for 4" and 6" blowers to keep anything from being sucked up into them, and...

www.thingiverse.com

3 Hooks for Grow Tent by EliotFR

I've design two hook to hang my grow light in my grow tent.The first one is design for snap hook and the second one have just a notch to slide in a rope.update 1 : I've had a new style, design to fit with the upper pole who have a flat end.It was design for 16mm bar and 4mm snap hook ( hole...

www.thingiverse.com

Grow tent pole clamp for fans by CorrieD

These are simple anchors that snap onto the poles of your grow tent for clamping small fans to.These snap fit onto 16mm poles. There are a few version, I was playing around with the shape optimization in Fusion 360. The one named clampvertallfinal should be the strongest, most secure one.EDIT...

www.thingiverse.com

6" - 6 Inch Ducting Grow Tent Mount by DotScott1

NOTE: This can be scaled up or down for 4" or 8" ducting but you would need to determine what size screws you would need. What you'll need: 8x12mm screws and nuts.Duck Tape. Ducting ClampsInstructions: I made this a square because squares are easier to cut than perfect circles. So... Cut a ~6x6"...

www.thingiverse.com

Sliding Window Dryer or AC Vent Seal Kit with 4" Air Duct Mount by DotScott1

UPDATE: Added a V2 option that uses less plastic and doesn't require you to open your window as much. Had some extra filament, needed a window vent. This was cheaper and faster than ordering one online :) The current model is designed to be printed on a large scale 3D printer like the CR-10S 400...

www.thingiverse.com

Fan Shroud for Heated Chamber Connect an 80mm Fan to 100mm Ducting by 3D_Market

Simple adapter to allow a standard 80mm fan to be used in conjunction with 100mm Ducting.

www.thingiverse.com

Tracker · Apr 9, 2021

anexgrower said:
For your grow tent, or a herb grinder, or a bong?
I'll include my collection of things I may want to print in the near future:

Grow Tent Accessories by dalelovelace

Accessories I have made for my Apollo 2x4 grow tent. The poles on the Apollo are 0.65" so these should work with any tent that has 0.65" poles.Link to my grow tent:https://amzn.to/30TKHOsAlso included are intake grates for 4" and 6" blowers to keep anything from being sucked up into them, and...

www.thingiverse.com

3 Hooks for Grow Tent by EliotFR

I've design two hook to hang my grow light in my grow tent.The first one is design for snap hook and the second one have just a notch to slide in a rope.update 1 : I've had a new style, design to fit with the upper pole who have a flat end.It was design for 16mm bar and 4mm snap hook ( hole...

www.thingiverse.com

Grow tent pole clamp for fans by CorrieD

These are simple anchors that snap onto the poles of your grow tent for clamping small fans to.These snap fit onto 16mm poles. There are a few version, I was playing around with the shape optimization in Fusion 360. The one named clampvertallfinal should be the strongest, most secure one.EDIT...

www.thingiverse.com

6" - 6 Inch Ducting Grow Tent Mount by DotScott1

NOTE: This can be scaled up or down for 4" or 8" ducting but you would need to determine what size screws you would need. What you'll need: 8x12mm screws and nuts.Duck Tape. Ducting ClampsInstructions: I made this a square because squares are easier to cut than perfect circles. So... Cut a ~6x6"...

www.thingiverse.com

Sliding Window Dryer or AC Vent Seal Kit with 4" Air Duct Mount by DotScott1

UPDATE: Added a V2 option that uses less plastic and doesn't require you to open your window as much. Had some extra filament, needed a window vent. This was cheaper and faster than ordering one online :) The current model is designed to be printed on a large scale 3D printer like the CR-10S 400...

www.thingiverse.com

Fan Shroud for Heated Chamber Connect an 80mm Fan to 100mm Ducting by 3D_Market

Simple adapter to allow a standard 80mm fan to be used in conjunction with 100mm Ducting.

www.thingiverse.com

I'm watching this, and I'll post anything I print to use in the tent.

anexgrower · Jun 11, 2021

air filter (activated charcoal) by adm1413

air filter is basically for filtering toxic gasses from the printer while printing.activated carbon is used as a medium.I was inspired from the idea on instructables but i was not able to find all parts so here it is !http://www.instructables.com/id/Activated-Carbon-Air-Filter/you can find the...

www.thingiverse.com

Strawberry Pot Desiccant Jar by debren27

This is a silica gel bead desiccant holder that prints quickly and easily in spiralized/vase mode, ideally with double line width for strength. The air holes are created by the upside-down half-cones.Many thanks to Angus at Maker's Muse for the inspiration! http://youtu.be/HZSFoFYpBaA?t=468sThe...

www.thingiverse.com

Plant Watering Bulb for Vase Mode by SnickerdoodleFP

Running low on my first spool of filament, I wanted to create a watering bulb that would do the job with very little plastic, and print quickly enough for a small garden. Ideally, a vase mode print. I designed this watering bulb to be watertight when printed with vase mode, so I tried to stay...

www.thingiverse.com

Printer-Friendly 2" Hydroponic Net Cups by Geodude1852

I made a net pot design that can be printed easily with no supports. I saw other designs that either left out the bottom surface or provided a version with built in supports so the bottom can be printed. This model can be printed entirely with no supports.

www.thingiverse.com

Weighted hydroponics airstone aquarium bubbler by unknowndebacle

This bubbler is CHEAP and quick to print, produces nice even bubbles even at low flow rates, and is weighted for maximum effectiveness! I used inert ceramic 'Mrs. Anderson's Pie Weights' but could substitute marbles. This is a remix from two other...

www.thingiverse.com

Hydroponic Drain by vik

This is a hydroponic trough drain for rectangular trough NTF systems http://en.wikipedia.org/wiki/Nutrient_film_technique . It's also useful for draining tubs and barrels and uses a standard (even in this metric world) 3/4" BSP threaded section which is just over 1" (26mm) in diameter. There's...

www.thingiverse.com

Tent no light leaking passive cooling room vent by kupec123

Tent no light leaking passive cooling room vent for the roof of tent. As we know hot air goes up that is why no fan is needed.UPDATED FINAL 26.4.2019Dimensions : 120x80mm and 150x100mm aproxPrint details:layer 0.2infill 20%For one vent u need 1x or 2x Plate and 1x Vent and 4x 3mm screws and...

www.thingiverse.com

Light Trap for computer fans by Fred2606

Light Trap for growbox that uses 120mm or 80mm fans.Nothing fancy, but everything was designed with the goal of improving air flow.Here in Brazil we do not have a good quality mat black fillament, so I had to print it gloss black and paint to it ensure blackout.Inspiration for this were from...

www.thingiverse.com

Grow Tent Blackouts by pajpoulter

I find these are better than just trying to pull the vent holes tight. Completely new at this so I'm sure the print setting could be better, please check them.

www.thingiverse.com

Customizable Satisfying Twist Container by larsch

This is a customizable version of Make Anything's Satisfying Twist Container in OpenSCAD. The shape, height, radius, smoothness and twist can be customized. Demo video.The generated models are solid (filled in) and need to be printed in Vase Mode. In Cura this is called 'Spiralize Outer Contour'...

www.thingiverse.com

Shower Head (Customizeable) by dsnettleton

Create a Shower Head to your own liking using the MakerBot Customizer App!

www.thingiverse.com

Mouth suction adapter for freezer bags by arpruss

For quick and dirty vacuum sealing of frozen goods, one can just suck air out of the freezer bag. However, doing that directly by mouth is unsanitary. Hence this adapter. Zip the bag almost shut, leaving just enough space for the eye-shaped part of the adapter. Press the bag around this part...

www.thingiverse.com

Sieve (3mm diameter holes, customizable) by plaztech

I printed this to sift through shredded plastic before feeding it to my filament extruder. I wanted something with round holes, and all the other sieves I saw on here had square ones. The holes are 3mm in diameter. The sieve is 8cm deep and 16cm in diameter, with 5mm thick walls.I've included...

www.thingiverse.com

My Customized Parametric Net Pot / Net Cup for Hydroponics / Aeroponics / Fogponics by irbrian1

Customized version of https://www.thingiverse.com/thing:790339Created with Customizer! https://www.thingiverse.com/apps/customizer/run?thing_id=790339

www.thingiverse.com

3D-printable faucet-to-hose adapter by CreativeTools

One of our favourite applications for 3D printing is to quickly manufacture something that is hard to find in stores. Recently we needed to connect a flexible hose to a standard water faucet in our office.Instead of getting into the car for a ride to a bunch of hardware stores, we quickly...

www.thingiverse.com

Clifford The Master Double Perc Ice Chamber by MNicky008

This is it, about as good as it gets, Version 5 Has been analyzed in ANSYS CFD (Computational fluid dynamics) for optimal drag free hits. Percs have been enlarged from V1 and improved printing structure. Snap rings have been made so pieces snap together, and will not separate without force...

www.thingiverse.com

Customizable ventilation grid by kakiemon

There is a newer Version available with many more possibilities - see: https://www.thingiverse.com/thing:5188211This ventilation grid is a remix of Thing https://www.thingiverse.com/thing:3115753I added the possibility to change the witdh in addition, not just length and diameter.Now its...

www.thingiverse.com

120 mm Fan Bucket Mount and Light Trap by stabone831

Needed to mount a 120mm pc fan to a 5 gallon bucket for a Space Bucket build.

www.thingiverse.com

LST Clip V2 AND V3 ADDED by JeenyusPete

V3 ADDED! LST plant training clips, made for marijuana plants but can be re-sized Now with Larger sized pre-made and slightly altered. Tiny Size, same design as regular size just smaller!

www.thingiverse.com

GreenJayPackerKS by ArdvarkMadman

A device for holding king size cones for filling with your herb of choice. Designed using OpenSCAD$fn=144;//RAW 1.25 size//cone_len_mm=80;//RAW classic king...

www.thingiverse.com

Open Source Universal Ball Joint (to reuse!) by DieZopfe

PROJECT PRESENTATIONI share with you the source files allowing you to make a solid ball and socket connection to reuse in your designs.This version is the result of a long series of iterations to find the right design. This ball joint allows to have a displacement of 25° from its axis, and at...

www.thingiverse.com

Ball joint mounts for grow tent by grownan

Remix of Ball joint phone mount with tripod mount from anovedhttps://www.thingiverse.com/thing:1035943added parts to connect to mars hydro tent poles as well as useful models for mounting items to them. PVC models are for 1/2 in pvcused M4 machine screw and M4 wingnut

www.thingiverse.com

120mm to 4" Exhaust Fan Shroud for Grow Tents by needypoo

This design was created so it could be hung inside of a grow tent via handy mounting holes! Sandwich a 120mm Fan with THIS to exhaust your quantum board grow light heat! Or put positive pressure and make a generator! This takes a 120mm fan and adapts it to a 4" exhaust...

www.thingiverse.com

Earth Bucket Container Garden by 2manytoyz

This is my first test of a self watering planter, using a 3D printed platform. The platform sits above the water line, allowing the plant roots to air prune. One part of the platform has a tube that allows a column of dirt to sit in the water. This wicks up the water, and keep the dirt moist...

www.thingiverse.com

Reusable Plant Root Growing by kubat

PLEASE READ THE DESCRIPTIONThe pictures are not mine, I just see an add and 3D modeled the product they are selling, oficial link in the below:https://www.kbxgsa.com/products/reusable-plant-root-growing-boxMy design is not a copy of the original, but a modified version that save plastic and need...

www.thingiverse.com