My somewhat unorthodox grow room.

Slyness41

Active Member
20180116_095325.jpg This is my design, I built a room, then was think tanking what my set up should be...using a hood, 400watts system, a 440cfm fan, all NFTG nutes with slf100, nectar #4 mix soil, 2 small air movement fans.
I hated my last setup, lots of ductwork, was too small, heat issues. i had enough!
So first of all, the long ductwork was not helping my heat issues, so CHECK gotta fix that, and too small, fixed that, now how to make more efficient.
THIS was my solution. Fixed mounted hood, fan fixed also, and vented into my ceiling area. 2' or so TOTAL of ductwork, and NOW, how to get plantz to light.
I am in construction, and stumbled onto a 4'x2' piece of wire chase on a job and LIGHTBULB.....use this as my table so to speak, and use ratchet straps on corners so it floats, THEN I can adjust plants to light instead! The adj system holds 100# per pair, so weight is fine. It's easy to adjust, works great, and plants can be as close as I want with little effort.
I have a filtered 10"x10" vent hole in lower part of room for fresh in, room never goes above 82, never lower than 71. Hum is always at 35-45%. So far is going perfectly, juzt curious if anyone else has seen the setup I'm using. Any thoughts would be awesome!!!
 

Hydrowannabe

Well-Known Member
That’s pretty ingenious! I can see a large advantage of being able to adjust the plants instead of the lights is that you could work in your reservoir much easier. Nice job
 

Slyness41

Active Member
That’s pretty ingenious! I can see a large advantage of being able to adjust the plants instead of the lights is that you could work in your reservoir much easier. Nice job
Yea I've never seen anyone do it, and I HATED all the ducting everywhere! This certainly solved the issue with that, and performs very well! Temps never go over 82. Might get a speed controller, then I can adjust venting to get a little bit better temp, was hoping for 84, won't do it now, too good exhaust.
 

Slyness41

Active Member
Yea I've never seen anyone do it, and I HATED all the ducting everywhere! This certainly solved the issue with that, and performs very well! Temps never go over 82. Might get a speed controller, then I can adjust venting to get a little bit better temp, was hoping for 84, won't do it now, too good exhaust.
It adjusts really easy, even going diwn, because of it being corner to corner, ut doesn't tip at all.
 

mmjmon

Well-Known Member
Where's the runoff going??

View attachment 4080075 This is my design, I built a room, then was think tanking what my set up should be...using a hood, 400watts system, a 440cfm fan, all NFTG nutes with slf100, nectar #4 mix soil, 2 small air movement fans.
I hated my last setup, lots of ductwork, was too small, heat issues. i had enough!
So first of all, the long ductwork was not helping my heat issues, so CHECK gotta fix that, and too small, fixed that, now how to make more efficient.
THIS was my solution. Fixed mounted hood, fan fixed also, and vented into my ceiling area. 2' or so TOTAL of ductwork, and NOW, how to get plantz to light.
I am in construction, and stumbled onto a 4'x2' piece of wire chase on a job and LIGHTBULB.....use this as my table so to speak, and use ratchet straps on corners so it floats, THEN I can adjust plants to light instead! The adj system holds 100# per pair, so weight is fine. It's easy to adjust, works great, and plants can be as close as I want with little effort.
I have a filtered 10"x10" vent hole in lower part of room for fresh in, room never goes above 82, never lower than 71. Hum is always at 35-45%. So far is going perfectly, juzt curious if anyone else has seen the setup I'm using. Any thoughts would be awesome!!!
 

Slyness41

Active Member
I have a heavy thickness plastic concrete mixing tray, is 8" high on sides. Sits under the pots so when I flush, etc. it just goes into the tray, then I can take outside and dump/ clean and dry.
 

Ednun

Member
Interested in your ductwork or if you had a better pic.
I'm still in the planning stages but was thinking along the same lines, fixed lamps and fans, movable tray suspended by four points to a single pulley system. Haven't built it yet, still gathering materials. I like your design too!
 

Slyness41

Active Member
The only ductwork is two adjustable 6" 90 degree pipes, hard pipe not sift, it's a basic 90 twist to align vent pipe. I think it's for gas?? They sell them at home Depot. Other than that, it's a 6" piece of insulated flex pipe between the fan and hood so I can access my bulb, and a random piece on intake so I could move it around until I found the Sweet spot for heat removal. Around 3' total of ducting. I'll send pic here in a few
 

1212ham

Well-Known Member
I like the hanging shelf idea. (: I had plants on an adjustable shelf, but I had to take everything off the shelf to change height.
 

Slyness41

Active Member
It works really well, just finishing up the end of my first run with this setup. Haven't seen anything concerning, pretty user friendly. Use the good quality ratchets though.
 
Top