NeWcS
Well-Known Member
Been growing a while now and have never had plants just start dying. They look great going into flower, then at about week 4-5 they just start dying from the bottom up.
25 gallon res. / starting water 12ppm(.5) - pH 7.9
BLOOM:
Silica @ 1mL/gal
Foliage-pro @ 4ml/gal
Mag-pro @ 2mL/gal
Alaska bloom 0-10-10 @ 1mL/gal
Comes out to around 700-800ppm
VEG:
Silica @ 2mL/gal
Foliage-pro @ 2mL/gal
Mag-pro @ 1mL/gal
300-400ppm
Brick coco(GH or mother earth) and perlite. Veg plants go from #1 pots into #7 pots, day 1-5 of flower. I don't rinse, or buffer or any of that shit. I don't have the kind of situation where I can move around a bunch of water to do that. I understand this can be part of the issue, but I have been using these brands and method for 10+ years. So I am fucked up why this is happening.
pH pen is stored in KCI solution and is calibrated @ 2 points. Reading against drops read in the same range.
When I mix my bloom res. the pH sits at 6.2, till the next day. When it's in the 3s and 4s. wtf? I'll raise it to 6. And next day, same thing, or not. Sometimes it'll hold strong overnight, sometimes not. pH up I've used. GH, AN, pure potassium hydroxide, potassium bicarbonate.
I will say it has been hot, dry and smoky these past few weeks or so. The max I've seen in the tent is 86f. Yikes, but not crazy crazy. There is good air flow at the bottom and top of the tent. Passive input with exhaust in the tent. Fresh air comes from within the home and a passive input from outside.
Not really sure what to do at this point. Just pH water flush, I guess. But not sure if that's just going to add to the issue, as I don't know what the issue could be.
Can't tell shit from the images but thought I'd post them anyways...
The heat is over for the year and its cool temps from here on out. I am hoping this to be my saving grace. But idk.
And help is much appreciated. Thanks
25 gallon res. / starting water 12ppm(.5) - pH 7.9
BLOOM:
Silica @ 1mL/gal
Foliage-pro @ 4ml/gal
Mag-pro @ 2mL/gal
Alaska bloom 0-10-10 @ 1mL/gal
Comes out to around 700-800ppm
VEG:
Silica @ 2mL/gal
Foliage-pro @ 2mL/gal
Mag-pro @ 1mL/gal
300-400ppm
Brick coco(GH or mother earth) and perlite. Veg plants go from #1 pots into #7 pots, day 1-5 of flower. I don't rinse, or buffer or any of that shit. I don't have the kind of situation where I can move around a bunch of water to do that. I understand this can be part of the issue, but I have been using these brands and method for 10+ years. So I am fucked up why this is happening.
pH pen is stored in KCI solution and is calibrated @ 2 points. Reading against drops read in the same range.
When I mix my bloom res. the pH sits at 6.2, till the next day. When it's in the 3s and 4s. wtf? I'll raise it to 6. And next day, same thing, or not. Sometimes it'll hold strong overnight, sometimes not. pH up I've used. GH, AN, pure potassium hydroxide, potassium bicarbonate.
I will say it has been hot, dry and smoky these past few weeks or so. The max I've seen in the tent is 86f. Yikes, but not crazy crazy. There is good air flow at the bottom and top of the tent. Passive input with exhaust in the tent. Fresh air comes from within the home and a passive input from outside.
Not really sure what to do at this point. Just pH water flush, I guess. But not sure if that's just going to add to the issue, as I don't know what the issue could be.
Can't tell shit from the images but thought I'd post them anyways...
The heat is over for the year and its cool temps from here on out. I am hoping this to be my saving grace. But idk.
And help is much appreciated. Thanks
Attachments
-
1.6 MB Views: 37
-
1.2 MB Views: 36