First grow in coco (peyote WiFis)

C

Clm307

Active Member
Sup guys this is my second grow and first in coco so hopefully I can make it through without to many problems , any and all suggestions would be greatly appreciated

3x3x6 tent
General hydro 3part ,diamond nectar, rapid start, liquid cool bloom
260w quantum board( at half power about 3ft away) 24 hr
coco perlite mix (washed and buffered with cal mag twice)
2 peyote WiFis
RH 75%
temp 80f

Germinated by soaking two hours then placing in wet paper towels , then placed in jiffy pellets

Seed broke surface on 6/22
Gave first watering at 6/25 which I thought was a ec of 300 but actually was 1000( due to faulty ec meter )
this went on for the last two days till I got a new meter today . So I don’t know what to do but give a proper diluted dose tomorrow and hope for the best but as of now they look healthy ‍..like I said I’m new to this but I have done a lot of research. suggestions would be much appreciated
 

Attachments

C

Clm307

Active Member
Day 8
Watered to runoff about 20%
ph6.2
Ec 450
Run off ec 850?? ....tomorrow I guess I’ll water with the same ec or slightly diluted to try and bring runoff ec back in an acceptable range? Anybody got any thoughts?
 

Attachments

A

Alphonso OG

Well-Known Member
Clm307 said:
Day 8
Watered to runoff about 20%
ph6.2
Ec 450
Run off ec 850?? ....tomorrow I guess I’ll water with the same ec or slightly diluted to try and bring runoff ec back in an acceptable range? Anybody got any thoughts?
Click to expand...
Clm307 said:
Day 8
Watered to runoff about 20%
ph6.2
Ec 450
Run off ec 850?? ....tomorrow I guess I’ll water with the same ec or slightly diluted to try and bring runoff ec back in an acceptable range? Anybody got any thoughts?
Click to expand...
Yes you can flush feed. For example Ill feed @ 500 ppms and wont stop until I get the same at the run off or your aiming target.

Yes you use more nutrients this way but Its keeps the range in check esp with coco.

If you let the coco dry out completely it will also raise your ppms when you do feed.

My ph range is 5.8
 
C

Clm307

Active Member
Alphonso OG said:
Yes you can flush feed. For example Ill feed @ 500 ppms and wont stop until I get the same at the run off or your aiming target.

Yes you use more nutrients this way but Its keeps the range in check esp with coco.

If you let the coco dry out completely it will also raise your ppms when you do feed.

My ph range is 5.8
Click to expand...
Alright cool that’s what I needed to hear...think I should right away or wait till tomorrows fertigation?
 
A

Alphonso OG

Well-Known Member
You can flush it to get it to around 350 ish max 450. Then let them go every 2 almost 3 days in between. Also do those solo cups have holes for proper draining?
 
C

Clm307

Active Member
Yeah I was gonna bring it down to around there after seedling stage.. I keep the pH of my inflow between 6.2 and 6.4 because this improves calcium solubility during this sensitive time
 
C

Clm307

Active Member
Noticed the leafs on both girls have weird coloration to them ?? Think I might of had my light (qb) on a little to high and started getting a little light burn??? Can anyone give me an opinion on what they think is goin on?
 

Attachments

C

Clm307

Active Member
I think it might be from diluting my nutrients to get to target ec with just RO water I will start diluting with cal mag water and see if that helps
 
You must log in or register to reply here.
Top