Club 600

Guzias1

Well-Known Member
Did u jb weld right away or later on I think ime going to jb weld now just got.all new equipment same chamber New pump etc oil slick pads slick balls etc

hhaa, mannnnnnnnn, when i got this, i wasnt confident in the joints..

i tested one vacuum in it over night, just a test run, no material, i woke up and the thing lost half its vac..

SO, went to auto store, spent a lot of time looking at specs on all the epoxies... well, JB weld blasted all of them out of the water.. :]

plenty of heat rating, i welded up the handled fittings as you can tell, no shame in appearance :]

the part with the valve, i just reallyyy tightened up, its got taped wrapped across the threads already, and i feel the tape was good, but i sure was able to snug her up quite a bit more..

i gots a small 3cfm pump, takes about 10 minutes or so to reach a full vac to where i can close her off the chamber..

slick pads slick balls? lolll what the hell

kiss-assParchment Paper
 

DrKingGreen

Well-Known Member
Sorry about your pup man. I don't know what I would do without my boy.

As for the jar method... Would I really have to use keef with that method or could I still use trim? Also, don't you think it's a little dangerous without a hole on the other end to release pressure? Maybe I could use a diamond tip and drill the proper size hole on the bottom of the jar, then use the other side as a filter so no built up pressure would occur
 

method2mymadness

Well-Known Member
Thanks guys he was just getting old had hip problems and got sick really swollen over night just weird talked with the vet and instead of him suffering had him put down I didn't want to but dnt want him to be in pain and uncomfortable for my.selfish reasons of just not wanting to let go they said it was the best thing and I did all I could do for him
 

method2mymadness

Well-Known Member
hhaa, mannnnnnnnn, when i got this, i wasnt confident in the joints..

i tested one vacuum in it over night, just a test run, no material, i woke up and the thing lost half its vac..

SO, went to auto store, spent a lot of time looking at specs on all the epoxies... well, JB weld blasted all of them out of the water.. :]

plenty of heat rating, i welded up the handled fittings as you can tell, no shame in appearance :]

the part with the valve, i just reallyyy tightened up, its got taped wrapped across the threads already, and i feel the tape was good, but i sure was able to snug her up quite a bit more..

i gots a small 3cfm pump, takes about 10 minutes or so to reach a full vac to where i can close her off the chamber..

slick pads slick balls? lolll what the hell

kiss-assParchment Paper
Well ur supposed to jb weld thos rivets the company said ...and oil slick balls are non stick concentrate containers oil slick pads. Are a non stick pad that will take place of ur parchment u can even blast straight on to them for nothing is lost from scraping.dish look up oil slick pads on YouTube and oil slick balls
 

cannabiscult

Well-Known Member
lol thanks doobie i cheatedlol sorry method bud thats a bummer man, il keep you in the thoughts when im smoking brother.


dr. yes youre correct it is a tad dangerous but i burp the jar as son as i feel the pressure build up.
 

method2mymadness

Well-Known Member
lol thanks doobie i cheatedlol sorry method bud thats a bummer man, il keep you in the thoughts when im smoking brother.


dr. yes youre correct it is a tad dangerous but i burp the jar as son as i feel the pressure build up.
Fuck I never realized ur name was cannabiscult I thought was cannabiscut not cannabis-cult
 

DrKingGreen

Well-Known Member
lol thanks doobie i cheatedlol sorry method bud thats a bummer man, il keep you in the thoughts when im smoking brother.


dr. yes youre correct it is a tad dangerous but i burp the jar as son as i feel the pressure build up.
What do you think about the drilling idea? I guess I could just say f it and put on a mask, thick clothing, gloves, safety glasses, and go your route... I'm just a bit scared lol. I saw a nasty accident in chem 2 my sophomore year and don't want to be on the same end of the stick as that girl! Don't remember what we were working with, but she did a reaction in a sealed container and glass went flying!
 

DoobieBrother

Well-Known Member
(just catching up with all the posts)
Sorry to hear about your friend , method.
They sure do leave a big empty spot in the heart when they move on to next level.
 

cannabiscult

Well-Known Member
yes yes yes.....cannabis CULT no biscuit but i guess thats ambers nick name for me lol anyway man i wouldnt get too scared, just wear all the protective gear and take it very very slow. the drill idea will work i just havnt done it.
 

Guzias1

Well-Known Member
Well ur supposed to jb weld thos rivets the company said ...and oil slick balls are non stick concentrate containers oil slick pads. Are a non stick pad that will take place of ur parchment u can even blast straight on to them for nothing is lost from scraping.dish look up oil slick pads on YouTube and oil slick balls

here is my experience with blasting onto that stuff...

P.S. dont blow yourself up people! .. ok now
[video=youtube;NIqGS50k6z0]http://www.youtube.com/watch?v=NIqGS50k6z0[/video]


i looked up the oil slick pad, in the video, is see the pad doing similar things, warping and what not.. i want to know if that pad will stay to its perfect form after 50 blasts..

http://www.youtube.com/watch?v=D-vpP-0Ivbw
 
Top