Building qb96 for 2x2

SaHt420

SaHt420

Well-Known Member
I've used a hlg pre-made light but want a qb 96 so I have to put it together ik basic electrical so I'm not worried. I do not know exactly what all I need though.Screenshot_20221103-175117_Chrome.jpgScreenshot_20221103-194340_Chrome.jpg
The driver has a built in dimmer I believe but ik I want the ability to use the light at higher power in a bigger tent when upgraded so I went 150 watt. I only plan to run it around 100-130 though. I need wire connections made for harsh environments and a ac cable rated for power draw and that's it right? Is there a connection I need to go from other side of drive to light?
 
SaHt420

SaHt420

Well-Known Member
Do I need wires to connect the drive to engine or can I just wire the light right into the driver's wires?Screenshot_20221103-203840_Chrome.jpgimma go with this driver imma just order the wall plug with it rated for it an just splice it in. Is it important to use weather proof connectors made for the lights if I plan to use a humidifier? Or can u just use male to female basic wire connectors?
 
SaHt420

SaHt420

Well-Known Member
GretaWang said:
Yes, Light to driver then driver to the wall. WAGO connector is good to use.
Click to expand...
I ordered everything today light driver connectors and 18awg wall plug I just have to get wire to attach light to driver. Might just cut up a old extension cord.
 
J

jdoorn14

Well-Known Member
You should use a good heat sink with a thermal conductive pad to run those qb96 boards. You’ll want to make sure you don’t overheat the boards.

HLG used the SSTX heat sink with those in the HLG 225 fixtures they sold.

65903224-02AA-454A-9A6E-2686717EFD55.jpeg
 
PJ Diaz

PJ Diaz

Well-Known Member
jdoorn14 said:
You should use a good heat sink with a thermal conductive pad to run those qb96 boards. You’ll want to make sure you don’t overheat the boards.

HLG used the SSTX heat sink with those in the HLG 225 fixtures they sold.

View attachment 5223051
Click to expand...
HLG sells the boards along with the pin heatsink and the adhesive thermal pad for $69, which is what it looks like the OP purchased.

horticulturelightinggroup.com

QB96 Elite V2 Engine

QB96 Elite V2 is a white LED Board with boosted red spectrum. Each Board is powered by 64 high power white LED, 16 630nm Red LED and 16 660nm Deep Red LED.
horticulturelightinggroup.com horticulturelightinggroup.com
 
SaHt420

SaHt420

Well-Known Member
PJ Diaz said:
HLG sells the boards along with the pin heatsink and the adhesive thermal pad for $69, which is what it looks like the OP purchased.

horticulturelightinggroup.com

QB96 Elite V2 Engine

QB96 Elite V2 is a white LED Board with boosted red spectrum. Each Board is powered by 64 high power white LED, 16 630nm Red LED and 16 660nm Deep Red LED.
horticulturelightinggroup.com horticulturelightinggroup.com
Click to expand...
That's the exact same thing I ordered light with heat sink thermal pad combo. My bad not you other dude
 
SaHt420

SaHt420

Well-Known Member
Do I need to moisture proof the light it's self or connection on light? I only received one connector so I'm just wing the driver directly to the light. I plan to run a humidifier eventually.
 
SaHt420

SaHt420

Well-Known Member
so every light board I order gets refunded so any suggestions what board an heatsink an thermal pads to get so I can use my hlg-150-54 driver
 
You must log in or register to reply here.
Top