Search results

Hello sir! I have not tried making an arc with the LEDs but that does sound like a great idea, I'm gonna have to figure out how to do that. And no I only take pics during light time. I turn the LEDs off sometimes before I take shots. Never open the cabinet during night time though.

Hey guys! It's been a while but here are pics from 1st week of flowering. I keep the panels as close to the plants as possible as long as I get a full spectrum, but I'll do some research and see if it's a good idea to raise it 18" above. The left side of the canopy is way lower than the right...

my temps range between 22C to 28C with 39% humidity, is that ok? I'm in that trial and error stage of my grow

Hi guys, I have a cabinet that's 72" x 36" x 18" or 27 Cubic Feet I have a 75 CFM Exhaust fan blowing into a Carbon Filter and 2x 25CFM Rocketfish case fans blowing into the cab. My minimum CFM requirement should be 27cft / 3min = 9 CFM I also have the following factors that need to boost my...

thanks =D here are pics from last night, starting to transition into flower!

gonna start flowering by the end of the week!

Journal open to comments and suggestions =D cheers!

Hey guys, this is my first grow cabinet, the grow area is only 4.5sqft but I have 11 plants going so I need really good lights. I've been adding LEDs as we went along and now I'm at the following specs: 2x 90W LED UFOs about 20cm from the plants (Red/Blue) 3x 16W LED Grow Panels on the walls...

thanks for reassuring me guys, this is my first grow and i was worried that those LEDs were making my plants act up. I'll raise the side panels a bit to force them to grow upwards a tiny bit more, I'm mainly worried about canopy penetration with a plant as bushy as this thx again

hi guys, im 5 weeks into veg and my plants are very bushy. i've been keeping my ph5.8 and ppm650 here's what they look like now

hey guys this is my first grow, im about 4 weeks into veg but all my plants are a few days/weeks apart. the oldest being 4 weeks and the youngest being 2. i've been going really easy on the nutes because of this. ph5.8 ppm650 using GH Micro + Bloom im afraid to add more nutes because of the...

OK so im trying to recover my plants after being overwatered. turned off my drippers first of all, mounted 3 LED panels on the walls, running 2 bubbler air stones in my reservoir, 5" of roots are being fogged/misted. ph5.8 ppm500 here's what they look like now. The pic with no LEDs is...

hey guys it's been 2 weeks, heres where im at right now ph5.8 ppm550 are they recovering?

well heres what they look like 24 hours after changing water and adding more air stones the new tops are getting extremely green, is that good?

so hopefully i'm doing it right from here on, these are my current stats: ph: 5.3 (will adjust to 5.8 when i get home from work) ppm: 553 (will probably be a bit lower once i adjust the water ph) temp: 28c - 30c drippers are 15min on / 15min off 2x small air stone blocks 2x LED 90w UFOs co2...

Thanks mercarus, this should help me quite a bit

My drippers are now 15min on / 15min off

Ok so I managed to lower ppm to 553 and ph to 5.3 Really hope this helps. I also hit them with a big dose of spray n' grow. Trimmed the browning leaves

The pH of my water was 6.8 before nutrients, then at 6.2 with nutrients in, i adjusted it to 5.8 with pH Down. The formula I use for GH is Micro 5ml/gallon and Bloom 10ml/gallon. Should I change out the whole nutrient solution or just take some out and put in pH adjusted water until I hit a...

changed my nutrient solution to 5.8ph and 1053ppm using gh micro + bloom, and used spray n' grow also added a dual outlet air pump with 2 new air stones, so my roots should be getting way more oxygen now hopefully this helps if my ph still keeps rising with this solution then i will soak the...