it dont matter what you use. you could pop a hole in a jiffy pellet, rockwool, styrofoam, it dont matter. i usually just drop the seed in whatever (F the paper towels) and wait and see. i have a 3 inch netpot nft system going right now and believe me. the plants dont care about what they get started in. i have some plants in 6 inch rockwool with roots longer than your arm. and other plants in 6 inch rockwool just by itself. same size buds, same size plants. sorry im off topic, somehow got started talking bout rootmass.....So would rapid rooters be fine?
Timer..............also anyone know where i could get a UK 1min timer as my aerotbale currently on constantly as UK only has 15min timers
They're not showing any signs of stress or root damage, I more was wondering how much, if any, I can shave back the roots without damaging my plants.blocking the sprayers? idk. aeroponics, dripping water, dwc, idk if i have seen a difference. ive been doing hydro now for 3 years and they all seem so totally independent on the health and condition of your reservoir. but ya, sorry, im lit, if they block the flow, they gotta go. because the roots grow, where there is.....
The roots are tied directly to its counter part above ground if u cut root it will cause the health of that particular counter part to lose health dramatically...in which nutes will be redirected from other places to compensate therefore weakening the health of the whole...small pieces are not really noticed I had a root go down my drip line end and I pulled that kinda stuff with no problems at all ... u should have no noticeable change if it is a smaller secondary root but don't mess with the tap root you'll most likely lose the whole thingI have 27 Strawberry Haze in an AP on its second week of flower. The roots have started to grab sprayers and rail sprayers are mounted on, should I or could I cut the roots without much damage to end product? And, if so how much do I cut?
Thanks guys. Sound advice. I tried with one initially and it was obviously stressed so I will just deal with it this cycle. Maybe I'll switch from round 6" pvc to 6" x 6" fence posts then mount sprayers in upper corner...The roots are tied directly to its counter part above ground if u cut root it will cause the health of that particular counter part to lose health dramatically...in which nutes will be redirected from other places to compensate therefore weakening the health of the whole...small pieces are not really noticed I had a root go down my drip line end and I pulled that kinda stuff with no problems at all ... u should have no noticeable change if it is a smaller secondary root but don't mess with the tap root you'll most likely lose the whole thing
Wonin, any container that is light proof and water tight will work as the res in a veger. You could use 20 liter buckets for the top chamber. Maybe 2 ice chest's stacked?. Possibilities are endless. You have to think outside of the box sometimes.hi
im from UK and was wondering where i could get those rubbermaid buckets to make my own aeroponics veg buckets or a good UK water tight version as i cant find decent buckets/ resevoirs anywhere. Im currently using an amazon twin 32 for flowering which cost me £300 and a xstream for clones but ya cant even buy an aero veg table even if i did have the money.
any help greatly appreciated
I can't believe somebody as moronic as you made it to 2,400 posts. Why have you not killed yourself yet?Unless you want to get raided by the D.E.A I would not do it because a pound every three weeks will take alot of work.
how do you convert the us timers?Wonin, any container that is light proof and water tight will work as the res in a veger. You could use 20 liter buckets for the top chamber. Maybe 2 ice chest's stacked?. Possibilities are endless. You have to think outside of the box sometimes.
About your timer, I convert our $10US. 15/15 timers to run 40 sec on and 4 min +/- off. Never messed with a European 240 V timer tho. I could prolly figure it out tho. Problem is shipping overseas. BTW some have been using 15/15 with some success
I am waiting for the products to get here early next week. I did insulate the outside of the rez with reflectex (sp) and start using black garbage bags inside the rez to help with light control and cleanup and that has helped stabilize the temps some and the ph but I am running the room temp at 68-70F. With that room temp, I am seeing 68-70F rez temps and that was without the fan blowing directly on them. I did turn the fan so now it points right at the clone unit so hopefully that helps too.
I would like to run the temp in the room at 75-80 since I am running CO2 and would get some great growth but I just don't see how I could do that and keep the rez temps down. I guess we will see how the beneficial tea works out.
I just hope I can use the tea with this setup with no problems.
I did almost the same thing. At first, I tried the small blue Coleman ice packs tied together and that failed miserably! The packs were just to small so I switched to 2 liters and then 20 oz bottles and then finally ice probes. The bottles worked but the temp change was to drastic (mid 50s to high 60s), not to mention the bottles being a pain in the ass especially if you wanted to go away for the weekend or something.I freeze 2 liter soda bottles, I tye a string on them and just switch them out daily. lowers temps pretty good.