Harvest a Pound Every Three Weeks!
- Thread starter StinkBud
- Start date
andyman
Well-Known Member
use t-5's with dif types like 2700k mixxed with 4200k and 6400k light spectrums so you have it all, but use more of the 2700k color spectrum when budding. also you can use LED lights, there the shit if there good ones that are over 2 watts each led. The cheap ones on ebay that are not so good, the more expensive ones are better. Mix them with the
T-5's and the led's and you can grow in 3' area. I did it in a 4' area and had good results
Attachments
bonghitz420
Member
How do you suspend your cuttings in the net pots?
grandpabear3
New Member
with a neoprene insert
DubB83
Well-Known Member
LST or ScrOG them beeches. You can do it but not with a HPS on top. Look up flouro tubes and CFL grows they usually specialise in small area grows.
~GG420
DubB83
Well-Known Member
3 stationary 600W is your best bet of the options you listed. A 600W will not cover the entire length of a stinkbud system though. The 600W will want to illuminate a 3ft square area (depending on light hood) and if you build the system to stinkbuds dimentions you would be missing a few aero sites for light coverage.
I say either 3 1000W or get movers for the 3 600W.
~GG420
gabrownzfan
Member
new at all this but i do have 1 piece of important info - when drilling holes for sprayers - not sure if this mentioned but you need, and it works perfectly as i have tested this - a 10/24 drill bit & tap for the small holes (sprayers)
gabrownzfan
Member
yeah - for the sprayers you need a 10/24 drill bit & tap in the uUSA
grandpabear3
New Member
well thats funny my red head ez clone sprayers use an 11/32 bit
GringoLoco
Well-Known Member
Rocking 11/32 as well 
Blue Moonshine1
Active Member
dude your the man.... you could be a spokes men for medical marijuans every where... my 60 year old mom has smoked for 40 years and just had back sergury, the doctor rather her take oxy than smoke weed!!!! nuts man. KEEP IT UP!!!!! BRAVO
DubB83
Well-Known Member
Got a picture? I see you have some small aero cloners and hempy buckets and a green house grow. I'm interested in seeing this 8 stinkbud system on 4x 600W. Do you have the systems full? How are you getting enough light penetration and how are you lighting the furthest out sites without a mover? My 600W only works good in about a 3.5 foot square. It would never light the end of my aero unit unless I raised it too high and then you end up with less light penetration.
~GG420
EDIT: Just for reference here is SOG's 5 Stinkbud systems under stationary 4x 1000W HPS.
DubB83
Well-Known Member
Put the movers so that two 600W lights will go over the three systems. Basically 1/2 each system for one 600W. The light will go perpendicular to the systems fence posts. This way it will be like having 2 600W lights per each stink bud system.
~GG420
dagobaker
Well-Known Member
i have my entire setup on stinkbuddies.comGot a picture? I see you have some small aero cloners and hempy buckets and a green house grow. I'm interested in seeing this 8 stinkbud system on 4x 600W. Do you have the systems full? How are you getting enough light penetration and how are you lighting the furthest out sites without a mover? My 600W only works good in about a 3.5 foot square. It would never light the end of my aero unit unless I raised it too high and then you end up with less light penetration.
~GG420
EDIT: Just for reference here is SOG's 5 Stinkbud systems under stationary 4x 1000W HPS.
ill look for a link
i have both rooms in
i have a second room with 2 stinkbud systems under a 1000 and have a 3 post setup with 2 400 hps on a mover
http://stinkbuddies.com/simplemachinesforum/index.php?topic=523.0
cant find the other......check in flowering forum