Absorber
Active Member
Hello all ,
my name is Absorber or Abe for short .
I have a custom designed grow with proven results .
It uses a 3d printed bell syphon to flood and drain the four 15ltr buckets in each tent , i have two 4ft² tents with 1ft clone/mother section on the end making the tent sizes 4ft x 5ft in total each.
I run 1000w phlizon lights @480w tops ,i have a 3d printed light lifter to raise and lower the light as its to difficult with a scrog net and tent full of plants .
I have a 2 zone controller for the tents and a common 250mm extraction fan and carbon filter fitted under the floor and you can see the 3d printed purple Y piece with 3d printed electric shutters controlling air flow from each tent via a humidity sensor . The fan runs at half speed when 1 tent calls for fan ( regardless of which tent) and ramps up to full speed when second tent calls for fan .
I run cyco nutrients and calmag
Thats it no boosters or anyting else apart from ph buffers .
I have a chiller on the resevoir.
Ive just converted the second tent to a bell syphon settup as it out performed the SIP pots i had in there as a comparison .
Warning some potty language in video's
![Screenshot_20240818-185208_DuckDuckGo.jpg](/data/attachments/4519/4519797-2c402c746078d79abadd2a3883f003a8.jpg)
![Screenshot_20240818-185226_DuckDuckGo.jpg](/data/attachments/4519/4519798-2756c3bb7aaf599e4fcd3db1ef246b5b.jpg)
![Screenshot_20240818-185245_DuckDuckGo.jpg](/data/attachments/4519/4519799-d2de060f62dce4256beaadc34424ea47.jpg)
![Screenshot_20240818-185302_DuckDuckGo.jpg](/data/attachments/4519/4519800-c2c7bdcf88f8d55967aec85406fbd394.jpg)
Any questions are welcome
my name is Absorber or Abe for short .
I have a custom designed grow with proven results .
It uses a 3d printed bell syphon to flood and drain the four 15ltr buckets in each tent , i have two 4ft² tents with 1ft clone/mother section on the end making the tent sizes 4ft x 5ft in total each.
I run 1000w phlizon lights @480w tops ,i have a 3d printed light lifter to raise and lower the light as its to difficult with a scrog net and tent full of plants .
I have a 2 zone controller for the tents and a common 250mm extraction fan and carbon filter fitted under the floor and you can see the 3d printed purple Y piece with 3d printed electric shutters controlling air flow from each tent via a humidity sensor . The fan runs at half speed when 1 tent calls for fan ( regardless of which tent) and ramps up to full speed when second tent calls for fan .
I run cyco nutrients and calmag
Thats it no boosters or anyting else apart from ph buffers .
I have a chiller on the resevoir.
Ive just converted the second tent to a bell syphon settup as it out performed the SIP pots i had in there as a comparison .
Warning some potty language in video's
![Screenshot_20240818-185208_DuckDuckGo.jpg](/data/attachments/4519/4519797-2c402c746078d79abadd2a3883f003a8.jpg)
![Screenshot_20240818-185226_DuckDuckGo.jpg](/data/attachments/4519/4519798-2756c3bb7aaf599e4fcd3db1ef246b5b.jpg)
![Screenshot_20240818-185245_DuckDuckGo.jpg](/data/attachments/4519/4519799-d2de060f62dce4256beaadc34424ea47.jpg)
![Screenshot_20240818-185302_DuckDuckGo.jpg](/data/attachments/4519/4519800-c2c7bdcf88f8d55967aec85406fbd394.jpg)
Any questions are welcome