Proguard vs AiroClean420
- Thread starter Lilmink
- Start date
xox
Well-Known Member
there is also agriair and airROS. honestly i dont know the answer i was just looking at these types of equipment myself. from some observations i saw airROS has a controller i believe it measures the ppm in the room with there piece of equipment honestly id look into airROS since they seem to actually measure the ppm.
DoubleAtotheRON
Well-Known Member
I've used an AirROS 4014 for about 2 years now.
xox
Well-Known Member
should post up a video or some pictures id love to see how that thing works
DoubleAtotheRON
Well-Known Member
I did a testimonial video on their website. I have no affiliation with them other than use thier product. They asked if I could do a cell phone video of a testimony.... little did they know that I have like $20,000 worth of cameras, lights, wireless mic systems, editing software... so I guess they were happy with it...... www.airrosshield.com
xox
Well-Known Member
oh i believe you completely i couldnt locate the video im mostly just curious how you set one up, how the controller works, from my limited understanding you hafta swap some stuff every so often as it wears out how you change that etc, etc
DoubleAtotheRON
Well-Known Member
It's pretty much plug and play... The display/sniffer detects H203 down to the Billionth. Ideal range is 30 PPB. Just set your "set point" at 30PPB and start your grow out at say a 50% Power Factor.. as your grow gets smelly, you may see readings in the low 20's.. this is where you start bumping up the Power Factor to say 60-65% to keep the PPB at around 30. Pretty simple. The consumables are an air filter twice per year, a chamber once every 6 months, and a new sensor every year. After you do all of this, you are basically getting a new "engine".. it's a total rebuild. Power consumption is about that of a standard 75w light bulb.
xox
Well-Known Member
@DoubleAtotheRON thats a great video!
DoubleAtotheRON
Well-Known Member
They owe you some dough lol, I’m buying 2 systems because of your video and they’re very happy with what you’ve done for them.
Has this ROS generator reduced your mold issues almost 100%? I was looking into these units and didnt pull the trigger because they were pricey. It sounded too good to be true. That it could sanatize all the mold but not degrade your terps and not bad for humans.
DoubleAtotheRON
Well-Known Member
Yes… got the labs to prove it. Not gonna lie tho, I have pushed VPD all the way till harvest, and some strains do come back with detectable mold.. but those strains are just mold prone. Other strains in the same room will come back as “none detected” on a CFU scale.
DoubleAtotheRON
Well-Known Member
Who are you working with?
Thats crazy that it works that well. So the ones with a little mold still pass the 10,000 cfu limit though? And you dont ever have to cut off tops from rot running at optimal VPD? And thats with runing your room like 85 degrees and 60% RH through out bloom? I was trying to do that with no sanitization and would get hit prety good with rot on dense strains. Now been runing 60% RH through week 3 flower then keeping it at 50 and below after that.
DoubleAtotheRON
Well-Known Member
I had one strain that popped 500 CFU’s, but that’s nothing. No topping of the colas. I finished my last run at 83 degrees/60rh
DoubleAtotheRON
Well-Known Member
But!.. like I said, there are some strains that are just mold prone no matter what.
DoubleAtotheRON
Well-Known Member
I did have a strain (sample anyways) that was over 10,000, but the other 2 tested at “none detected” on one, and 500 CFU’s on the other, which is near nothing.