Bho vacuum chambers

Cgravell23

Cgravell23

Member
Jjgrow420 said:
Hm. I'm just in the bath
I'll take a pic of my setup. I run 2 pots. One filled with water with a heating mat underneath on a controller, then the vac chamber inside that pot. Keeps temps more stable.
Could just be the material ? I duno. Seems off to me tho.
Click to expand...
That’s exactly how im doing mine except that im using a 5x5 magnetic stirrer hot plate.
 
Jjgrow420

Jjgrow420

Well-Known Member
If you smoke a joint of it and it tastes poopie when you make concentrate well you're concentrating the poopie too and it'll taste poopie x100.
Lot of the time old outdoor weed that hasn't been stored properly, can taste like burnt rubber, piss, ammonia(piss I guess), burnt hair, all kinds of lovely flavours....
 
Jjgrow420

Jjgrow420

Well-Known Member
Cgravell23 said:
the 4-5 hour wait to flip will b done here around 8 & so ill get the temps checked without the lid on then.
Click to expand...
4-5hr wait to flip? Are you flipping it over and over? I just flip once. When it's flat it's done
The more you flip the more air you put into it it and then re vac it out just agitating the slab. I'm a firm believer in less agitation the better.
 
Cgravell23

Cgravell23

Member
Jjgrow420 said:
4-5hr wait to flip? Are you flipping it over and over? I just flip once. When it's flat it's done
The more you flip the more air you put into it it and then re vac it out just agitating the slab. I'm a firm believer in less agitation the better.
Click to expand...
Ohhhh shiiit ok. I read the CapN article on the dudegrows.com/patreon.org
 
Cgravell23

Cgravell23

Member
This article says to flip it every 4-5 hours for the first 24 to 48 hours and for the last 24 hours to flip it every 10-12 hours.
 
lusidghost

lusidghost

Well-Known Member
Cgravell23 said:
I have a vevor 2 gallon chamber with a vevor 1 stage 5 CFM pump & it works great, pulls a vac really quick and if u dont overtighten the nuts like on the gauge for the chamber it will hold the vac for days. But i was wondering if u knew anything about extracting? Cause i was wonderingvof when i put the butsne in since i didnt have the bottom valve open and allow the whole 300ml can in my 45 gram tube if my wax will come out ok?
Click to expand...
Do you mean your material column has a ball valve at the bottom? And you're wanting to blast into it while the valve is closed?
 
lusidghost

lusidghost

Well-Known Member
Cgravell23 said:
Yes i did blast the first half can in it wothout it being open, did that make the solvent soak the bud too much u think? Or not enough?
Click to expand...
Nah you're good. Some people let it soak for a while. I've tried a time or two. Supposedly if you let it soak too long can start pulling unwanted plant stuff like chlorophyll. The biggest issue is if the column is really cold the lipids can gelatinate, which is good, but they can also clog up your filter. Which was the issue I had.
 
lusidghost

lusidghost

Well-Known Member
Also I usually don't flip my paddy unless it seems like it really needs it after a few days in the vac oven. Typically I don't mess with at all until I think it's finished, then make the call to put it back in if it's a little tacky.
 
Cgravell23

Cgravell23

Member
52584E46-FA86-4E41-ABF9-65DC2FDBD13E.jpegHeres some of the material, now i have done three 45 gram runs and trashed the end product and i only have enough for about one more run as we’ve smoked on quite a bit of it. Lol!!!
 
Cgravell23

Cgravell23

Member
lusidghost said:
Also I usually don't flip my paddy unless it seems like it really needs it after a few days in the vac oven. Typically I don't mess with at all until I think it's finished, then make the call to put it back in if it's a little tacky.
Click to expand...
Ok awesome, thank you tons. Ive stirred it & scraped it back and forth with a blade & all kinds of stuff! ‍(Hand on forehand)
 
You must log in or register to reply here.
Top