Help with clones - no roots

sk34v

Member
hello all day 5 and still noting showing

i use

X-Stream Aeroponic Propagator Kits with Secret Jardin TLED, Clonex Gel & Mist
 

Attachments

  • 1.jpeg
    1.jpeg
    208.9 KB · Views: 39
  • 2.jpeg
    2.jpeg
    80.1 KB · Views: 43
To high moisture in tent/propagator, I would remove the hood. Try to remove it in short intervals in the beginning and then completely off. You don't need to run high humidity with Aero clones or in DWC. Different story with jiffy pucks and rockwool cubes. It will only cause problems from my experience.

It usually takes about a week for roots to show.
 
Keep the lid off them dude. You don't need a humidity dome when using an aerocloner.

I use DIY aerocloners and I don't use gel. It comes off the roots in no time. Just use regular Clonex @ 5mL/gal and pH to 5.5.

That being said, what's your water temp at? I've found that my roots shoot faster when the water temp is warmer, but you run the risk of bacteria. I use a DIY UC Roots which is basically just chlorine to ward off any bullshit. Once they have roots then the colder water temps are better for dissolved oxygen levels.

Are you using airstones? Again its just my experience but I prefer to run a couple in each of mine.

I'd also get those lights up a bit as they don't need any until they shoot roots. The plants can't handle the light as they have no way to photosynthesize and uptake nutrients since there is no roots. If you give em too much light they will used up the nutes in what little foliage is there and they will be fucked. I keep my cloners in the corner of my room away from the direct lighting. Just my 2 cents anyways..
 
Keep the lid off them dude. You don't need a humidity dome when using an aerocloner.

I use DIY aerocloners and I don't use gel. It comes off the roots in no time. Just use regular Clonex @ 5mL/gal and pH to 5.5.

That being said, what's your water temp at? I've found that my roots shoot faster when the water temp is warmer, but you run the risk of bacteria. I use a DIY UC Roots which is basically just chlorine to ward off any bullshit. Once they have roots then the colder water temps are better for dissolved oxygen levels.

Are you using airstones? Again its just my experience but I prefer to run a couple in each of mine.

I'd also get those lights up a bit as they don't need any until they shoot roots. The plants can't handle the light as they have no way to photosynthesize and uptake nutrients since there is no roots. If you give em too much light they will used up the nutes in what little foliage is there and they will be fucked. I keep my cloners in the corner of my room away from the direct lighting. Just my 2 cents anyways..

thank you for quick reply

i will remove the humidity its in my room and the humidity is always 60 temp of water is 22 i will check about the chlorine i have no aire stones

should i not use both lights it come with then Secret Jardin TLED
 
can i fix this

so today i moved the lights of the dome and removed the dome i added air pump and i check my water temp sits at 23/25
 

Attachments

  • hmmm.jpeg
    hmmm.jpeg
    217.6 KB · Views: 25
  • hmmmm.jpeg
    hmmmm.jpeg
    143.7 KB · Views: 24
  • testing.jpeg
    testing.jpeg
    111 KB · Views: 21
The plants you took these clones from were not very healthy.When I do hydro clones they wilt for 1 day then they stand proud.Your leaves are curled down,if they dont look good a day or two from now you should re think the plan.
 
The plants you took these clones from were not very healthy.When I do hydro clones they wilt for 1 day then they stand proud.Your leaves are curled down,if they dont look good a day or two from now you should re think the plan.

did not take pic day 1 thay did look very good

the humidity was 100% so i think thay got over waterd ?

the mum is very healthy
 
Your lights are way to high. Your clones will be thinking of stretching not growing roots, and with no roots to support a stretch they are dying.

Drop those lights right on top of them and they will go into root mode.

I mean at this point its a last resort.
 
did not take pic day 1 thay did look very good

the humidity was 100% so i think thay got over waterd ?

the mum is very healthy
ok there yellowing already though.Can be a good sign if you have little bumps starting.But could also be bad,good luck.
 
Your lights are way to high. Your clones will be thinking of stretching not growing roots, and with no roots to support a stretch they are dying.

Drop those lights right on top of them and they will go into root mode.

I mean at this point its a last resort.
No,wrong.Bad advice.
 
No,wrong.Bad advice.
Look at the plants lol
They aren't growing roots after a week?
His lights are 6 feet above his plants.

Not sure how you grow clones but in my world I have never grown clones with a light that high above.

And you really haven't give him any advice other then good luck.

What do you suggest to him? Stay on his current path? Lol

Anyhow OP, up to you but I'm pretty sure those are almost done so my advice isn't going to make them any worse lol
 
Your lights are way to high. Your clones will be thinking of stretching not growing roots, and with no roots to support a stretch they are dying.

Drop those lights right on top of them and they will go into root mode.

I mean at this point its a last resort.

the lights was on top of the domes for 6days i only just moved them today
 

Attachments

  • dasdasdasd.jpg
    dasdasdasd.jpg
    93.8 KB · Views: 7
Well my opinion
1. Take the vent off completely and don't put it back on
2. Lower the lights again

See what happens after 2 or 3 days
 
Clones don't need much light at all, I have mine sitting in between my veg tables the lights are atleast 5 ft away and off to the side, and plants are blocking a lot of it since they are so much taller. This round rooted in less than 10 days in just in root riot cubes in a dome.
 
Back
Top