DIY with Quantum Boards
- Thread starter robincnn
- Start date
Budzbuddha
Well-Known Member
Welp ...... Deep red is a necessary evil .... it does stuff to females .
My plants move the same way.
My plants move the same way.
Little Dog
Well-Known Member
I’m the new boy for sure. Yeah @pops, only the far red. And I’m not versed on it enough to know if I really need it or not. I am gonna add another HLG- 320. That’ll give me four of’em over a 5X7. I’m good with that. But does the far red actually help? From what I read, it does in its own way. I’m not sure when to use’em during the day/night cycle. But if they’ll help my plants, I’ll add them too. And I’ll figure out when to turn’em on and off.
By the way pops, I didn’t retro fit my hoods to use like I thought I was. Just don’t need’em. These things run so cool. It’s great, less AC, less dehumidifier, less chiller now too. And I got rid of all duct work, and a fan, plus two light movers. I checked my wattage at the wall with all that stuff and with the 2 600 HPS bulbs. Total wattage before was 1360 Watts. Now, with three 320’s I’m only running 800. And when I add another, I’ll start at 200 watts each. But I’ll have plenty of room to go up if needed. But my room is definitely cooler now! I’m not sure who said it. But I may have to add heat this winter. I’ve never had to do that before. My man was right.
By the way pops, I didn’t retro fit my hoods to use like I thought I was. Just don’t need’em. These things run so cool. It’s great, less AC, less dehumidifier, less chiller now too. And I got rid of all duct work, and a fan, plus two light movers. I checked my wattage at the wall with all that stuff and with the 2 600 HPS bulbs. Total wattage before was 1360 Watts. Now, with three 320’s I’m only running 800. And when I add another, I’ll start at 200 watts each. But I’ll have plenty of room to go up if needed. But my room is definitely cooler now! I’m not sure who said it. But I may have to add heat this winter. I’ve never had to do that before. My man was right.
Northernone666
Well-Known Member
Very Kool!!
Bubblin
Well-Known Member
Still tweaking the wire loom size, waiting for some smaller stuff but it's getting there.
2700k QB132s on a 1050ma driver, will be dialing it down to around 160 watts from the wall for this run.
Dual 4' T5s with agromax pure uv @ same height as the boards, on a short af timer loop.
2700k QB132s on a 1050ma driver, will be dialing it down to around 160 watts from the wall for this run.
Dual 4' T5s with agromax pure uv @ same height as the boards, on a short af timer loop.
Attachments
I have my room setup with 4ea) qb 288 & 4ea) qb 120's, and a 5 cob full spectrum fixture I built, I have a far red light bar that goes on at lights out for 20 min. I just added a solarcure fluorescent tube fixture for uvb. The room is 15 +- sq ft, 42" x 52". Also have a bunch of led tube fixtures on the walls for lower lighting.The whole ceiling is basically full but there is room to add 2 narrow fixtures, thinking about photo red but they would only be putting out 32w combined. Think this is even worth the effort, the components would cost about $148.00.
Attachments
Last edited:
pop22
Well-Known Member
I've got them all the qb's dimmed so the draw is approx 800w but some of that is fans, need to check what the 4" is pulling, estimate approx 600w for the lights only.
fragileassassin
Well-Known Member
21.92v-23.52v : board voltage range
2800ma : board max current
57 VDC to 114 VDC : driver voltage range
2800ma : continuous current output.
23.52x4 = 94v which is less than the 114v max of your driver.
If you wire the 4 boards in series, thats pretty much the perfect driver for that imo.
You'll be able to run all 4 at full power of 2800ma and arent at a risk of over driving current if you lose a board.
619kt619
Well-Known Member
HLG only gives one driver option for a 4 board set up in series. It's on the product page
https://horticulturelightinggroup.com/collections/all/products/qb120-quantum-board
https://horticulturelightinggroup.com/pages/qb120-board-guide-1
^ might want to use the board guide page instead of the products page.
^ might want to use the board guide page instead of the products page.
fragileassassin
Well-Known Member
A 240-c2100 is under powered for 4 boards and went push them to full power.
Humple
Well-Known Member
Not correct. I have two 4xQB120 fixtures, each run off an HLG-240H-C2100A, and at 254w for one and 257w for the other, the drivers push the boards past HLG's recommended max of 60w per board.
Could I add 4 more qb120s onto the hlg-240h-24a (total of 8 ) if I want to up the efficiency down the road?
diyled
Well-Known Member
Only If they all come out at a similar fv.