iso extracted mescaline

[indicat33]

91% Iso method- 3 days total. Here's the result from 56g of Peruvian Torch powder... evaporating. I x-tracted twice, both times getting a nice brownish/greenish/black layer. Upon trying a third time, I didn't get such thick/dark layer so I stopped with 3 .
Now all layers combined, and evaporating... tbc _~

 

[MrEDuck]

I hope you enjoy your cactus tar!

 

[indicat33]

I hope you enjoy your cactus tar!

Thanks ! This will be my 1-st mescaline experience. I hope to end up with approx. 500mg of mescaline from this pull. Will update this thread periodically _~

 

[MrEDuck]

You planning on doing it all in one shot? That's a heavy dose of mescaline (potentially very heavy) but not 2 good doses. Though it could be.

 

[indicat33]

You planning on doing it all in one shot? That's a heavy dose of mescaline (potentially very heavy) but not 2 good doses. Though it could be.

I estimate this to be approx. 500-550mg mescaline. 1gm x-tract=100g/mescaline. I am wanting to take 300mg myself and save the rest. My Gf wants to try it too-

 

[MrEDuck]

Split it and see

 

[rory420420]

you know my response to the dosing of anything so....have fun!

 

[indicat33]

now it's a waiting game... I don't wanna use heat /sunlight to dry it, so it may take a week or so

 

[Bublonichronic]

Put a fan blowing on it....have fun

 

[MrEDuck]

A fan will have it almost dry in an hour

 

[indicat33]

I wanna make sure All the iso evaporates before rolling that shit up into many pea-sized balls and dosing about 300mg (ideally 3gm) of cactus resin. Will have to plan it out well and go from there. Peace, peeps
_~

 

[indicat33]

Update: Got pissed off watching that shit take Aeons to dry... fan or no fan, it takes forever. I split the x-tract into 2 pyrex dishes and put it on very LOW heat on my electic stove.
I figured, even if all the iso evaporated, I would still be left with sludge, so I need to evaporate the H2o also. I want silly-putty, workable material I can roll into tiny balls (easier digestion). I scraped a tiny bit off the sides of the dish it was in previously (maybe 1/3g). BITTER AS FUCK... This Low heat is working well... under 120f so no alkaloid lost, yet it's drying this tar much faster now - TBC...

 

[rory420420]

hence my reccomendation of 99% iso...

 

[rory420420]

looks like youll have fun...nice adidas..

 

[indicat33]

The smaller of the 2 dishes is DRY - Scraped up a little over 2g... little sticky- but not too much. I can totally work with this. I estimate (hope) to have about 200+ mg / Mescaline here. Other half is still drying... I notice this resin is brownish-ruddy in color.. not quite black. Everything I have read indicates the presence of mescaline... Interesting note- upon scraping with a razor, I noted the resin kept forming Linear "Spikes"...
I understand a proper A-B X-traction yields spicules... interesting-

 

[indicat33]

Here's the entire x-tract from 56g Peruvian torch powder. About 7g extract that smells like a cactus plantation and tastes Supremely Bitter...

 

[indicat33]

hence my reccomendation of 99% iso...

I know- but my area only stocks 91% Iso... in retrospect, it worked out just fine. Dry, finished product I can mold into anything _~

 

[ilyaas123]

That is indeed a job well done; I'm starting 50 trichocereus bridgesii tomorrow followed by 100 peruvian torch cactus seeds or peyote.

 

[ilyaas123]

I know- but my area only stocks 91% Iso... in retrospect, it worked out just fine. Dry, finished product I can mold into anything _~

Have you had a look on eBay? I've seen quite a few sellers with 99% iso

 

[indicat33]

That is indeed a job well done; I'm starting 50 trichocereus bridgesii tomorrow followed by 100 peruvian torch cactus seeds or peyote.

Thanks bro.. I hear T. Bridgesii is indeed a powerful ally. I may try it next x-traction and see if there is a noticeable difference in potency. Good Luck and Happy Times !!! _~