TurboLobster
Active Member
ok well this i my make shift idea for a pc case growing room
bare with me as im just starting to think this out
i will post some drawings when i can
well you take a pc case and emptry it out. remove all the parts and fire down and hinges sticking out
we will not be cutting anything for this project so put them power tools away. lo
now you need to set up the fans and lights. first layer the inside with mylar. cover everything with it
now you are going take a knife or razor blade and cut out the holes for the air vents.
you would cut the orriginal fan hole out below the power supply, cut out the space for the power supply
one more to go. cut out everything underneth the buttons and lights of the front sides bottom.
now i wired my system in a strange way so please understand that you might have to do it your own way
i have a usb external hard drive. i took it apart and removed the usb device out of its case. i attached a
power cord spillter so now i could plug two fans up to the usb device. i put one under the power supply to
be a exhaustand then i put one on the front bottom part. you would crew them in and then secure the light
holes with cadboard covered in mylar. just glue it or run a screw through it.
(i have a reason why i used cardboard) so now you need to install the lights.
you would now take a cfl pulg and attach it to the the top part of the case. you would be rinnung the
pulg out the powersupply hole. you would then screw in the cfl light bulb. boom you have light. but i bet your
saying WTF WHY IS IT SO HIGH UP AND WAY FROM MY BABY???? well thats easy. its not the only light
you would attach a l bar into one of the bays and secure it with a screw so that the l part is faceing down and is extened at heast into the middle
of the case. attach the bulb and socket to the L and run the wire spiral over the part lwading to the bays and once it got to the entance of the bays
run it at a 45 degree angle out the power supply hole. once done take the power suplly and open it up. gut that bitch but keep the fan. remove the plug.
fit the two pulgs through the back end of the power supply and carefully. insert the power suplly back into the case.once in pull the wires gently to
remove all the slack. you would also be leading the usb wire out the power supply bay and after that take black electracle tape and tapre most of the three wires all the way down but leaveig five inches from the pulg and dont
forget to mark the top light cord with a red marker and the bottom light's cord with a black marcker.
pulg the empty space in the power supply pulg with rubber cement or something like that. let it dry. boom the case is half done.
next step get a container and fill it with soil. put the seeds in. put the container under your cfl (oh and ur putting a something undereath the container offcourse to collect the runoff water.)
now put a thermatore somewheree inside. hook the pulg with the black dot into a timer and hook up the timer into a extension cord.
hook up the usb plug and hit the switch so see them spin. the light should go on but ony the one near your plants.
close the door and look to see if you see any light leaks. find trhem andf pulg them with putty.
well set up your timer and let it grow
you can also rig a fan to blow out air next to the power supply but thats up to you.
OK i was beyond stoned when i wrote this. i didnt spell check and isk if it makes sense but take it as is.
its a gay idea but a idea non the less so when i sober up or if one of you reads and gives me your two productive cents we can maybe throw togethere something that will work.
oh and i still am baked so im off to go eat. i smoke two blunts of skunk with my friends and im flying
bare with me as im just starting to think this out
i will post some drawings when i can
well you take a pc case and emptry it out. remove all the parts and fire down and hinges sticking out
we will not be cutting anything for this project so put them power tools away. lo
now you need to set up the fans and lights. first layer the inside with mylar. cover everything with it
now you are going take a knife or razor blade and cut out the holes for the air vents.
you would cut the orriginal fan hole out below the power supply, cut out the space for the power supply
one more to go. cut out everything underneth the buttons and lights of the front sides bottom.
now i wired my system in a strange way so please understand that you might have to do it your own way
i have a usb external hard drive. i took it apart and removed the usb device out of its case. i attached a
power cord spillter so now i could plug two fans up to the usb device. i put one under the power supply to
be a exhaustand then i put one on the front bottom part. you would crew them in and then secure the light
holes with cadboard covered in mylar. just glue it or run a screw through it.
(i have a reason why i used cardboard) so now you need to install the lights.
you would now take a cfl pulg and attach it to the the top part of the case. you would be rinnung the
pulg out the powersupply hole. you would then screw in the cfl light bulb. boom you have light. but i bet your
saying WTF WHY IS IT SO HIGH UP AND WAY FROM MY BABY???? well thats easy. its not the only light
you would attach a l bar into one of the bays and secure it with a screw so that the l part is faceing down and is extened at heast into the middle
of the case. attach the bulb and socket to the L and run the wire spiral over the part lwading to the bays and once it got to the entance of the bays
run it at a 45 degree angle out the power supply hole. once done take the power suplly and open it up. gut that bitch but keep the fan. remove the plug.
fit the two pulgs through the back end of the power supply and carefully. insert the power suplly back into the case.once in pull the wires gently to
remove all the slack. you would also be leading the usb wire out the power supply bay and after that take black electracle tape and tapre most of the three wires all the way down but leaveig five inches from the pulg and dont
forget to mark the top light cord with a red marker and the bottom light's cord with a black marcker.
pulg the empty space in the power supply pulg with rubber cement or something like that. let it dry. boom the case is half done.
next step
get a container and fill it with soil. put the seeds in. put the container under your cfl (oh and ur putting a something undereath the container offcourse to collect the runoff water.)now put a thermatore somewheree inside. hook the pulg with the black dot into a timer and hook up the timer into a extension cord.
hook up the usb plug and hit the switch so see them spin. the light should go on but ony the one near your plants.
close the door and look to see if you see any light leaks. find trhem andf pulg them with putty.
well set up your timer and let it grow
you can also rig a fan to blow out air next to the power supply but thats up to you.
OK i was beyond stoned when i wrote this. i didnt spell check and isk if it makes sense but take it as is.
its a gay idea but a idea non the less so when i sober up or if one of you reads and gives me your two productive cents we can maybe throw togethere something that will work.
oh and i still am baked so im off to go eat. i smoke two blunts of skunk with my friends and im flying
