cannabisguru
Well-Known Member
I'm about to post some information I found regarding using a hygrometer, inside my curing jars.. in order to take the 'guess work' or and 'trial and error' out of the curing process. I have not tried this yet.. but I plan on trying it out, giving it a test run.. with some of my upcoming harvest.
I'm sure its been talked about around here before.. I just wanted to share this information with everyone else.
peace.. and enjoy!
Get a perfect cure every single time, using the hygrometer curing method: and here's how you do it:
This method is particularly effective for folks who are starting out, those looking to maximize quality in a shorter period of time, and folks who's like to produce a connoisseur-quality product each and every time with no guesswork involved.
It's a very simple and effective process:
Cut the product, trim it per your preference, but don't dry it until the stems snap. Take it down while the stems still have some flex, but the product feel dry on the outside. This is a perfect opportunity to drop the dry-feeling flowers onto a screen and collect prime-quality kief that would otherwise get lost in the jar.
Jar the product, along with a Caliber III hygrometer. One can be had on Ebay for ~$20. Having tested a number of hygrometers - digital and analog - this model in particular produced consistent, accurate results. Then, watch the readings:
+70% RH - too wet, needs to sit outside the jar to dry for 12-24 hours, depending.
65-70% RH - the product is almost in the cure zone, if you will. It can be slowly brought to optimum RH by opening the lid for 2-4 hours.
60-65% RH - the stems snap, the product feels a bit sticky, and it is curing.
55-60% RH - at this point it can be stored for an extended period without worrying about mold. The product will continue to cure.
Below 55% RH - the RH is too low for the curing process to take place. The product starts to feel brittle. Once you've hit this point, nothing will make it better. Adding moisture won't restart the curing process; it will just make the product wet. If you measure a RH below 55% don't panic. Read below:
Obviously, the product need time to sweat in the jar. As such, accurate readings won't be seen for ~24 hours, assuming the flowers are in the optimal cure zone. If you're curing the product for long-term storage, give the flowers 4-5 days for an accurate reading. If the product is sill very wet, a +70% RH reading will show within hours. If you see the RH rising ~1% per hour, keep a close eye on the product, as it's likely too moist.
HTH,
Simon
I'm sure its been talked about around here before.. I just wanted to share this information with everyone else.
peace.. and enjoy!
Get a perfect cure every single time, using the hygrometer curing method: and here's how you do it:
This method is particularly effective for folks who are starting out, those looking to maximize quality in a shorter period of time, and folks who's like to produce a connoisseur-quality product each and every time with no guesswork involved.
It's a very simple and effective process:
Cut the product, trim it per your preference, but don't dry it until the stems snap. Take it down while the stems still have some flex, but the product feel dry on the outside. This is a perfect opportunity to drop the dry-feeling flowers onto a screen and collect prime-quality kief that would otherwise get lost in the jar.
Jar the product, along with a Caliber III hygrometer. One can be had on Ebay for ~$20. Having tested a number of hygrometers - digital and analog - this model in particular produced consistent, accurate results. Then, watch the readings:
+70% RH - too wet, needs to sit outside the jar to dry for 12-24 hours, depending.
65-70% RH - the product is almost in the cure zone, if you will. It can be slowly brought to optimum RH by opening the lid for 2-4 hours.
60-65% RH - the stems snap, the product feels a bit sticky, and it is curing.
55-60% RH - at this point it can be stored for an extended period without worrying about mold. The product will continue to cure.
Below 55% RH - the RH is too low for the curing process to take place. The product starts to feel brittle. Once you've hit this point, nothing will make it better. Adding moisture won't restart the curing process; it will just make the product wet. If you measure a RH below 55% don't panic. Read below:
Obviously, the product need time to sweat in the jar. As such, accurate readings won't be seen for ~24 hours, assuming the flowers are in the optimal cure zone. If you're curing the product for long-term storage, give the flowers 4-5 days for an accurate reading. If the product is sill very wet, a +70% RH reading will show within hours. If you see the RH rising ~1% per hour, keep a close eye on the product, as it's likely too moist.
HTH,
Simon
