stevoXbaked
Active Member
Ok, here is a nifty little gadget I created yesterday. I guess it is a ?perculator?
add-on for most likely any type of bong, with atleast, a decent tube long enough to fit the gadget into the top, the longer the better perculation goes on!!!
Also, be4 I share my neat little gadget, and after you read this post, I'd appreciate if everybody [after you read this of course] reply back, and give me your constructive criticism, and answer me a few things:
| | <--*** PLZ READ: YOUR GONNA STICK THIS INVENTION ABOUT 1 INCH DOWN THE TOP OF THE TUBE!!! ***
| | @ <--Bowl piece (in foreign countries they use 'cones', I prefer the 1 hit bowls.
|o|// <--Stem (Can be slide-out, the o behind the stem inside the bong would be the carb-hole a.k.a. shottie, or "YOUR SUPPOSED TO USE THE SHOTTIE BE4 YOU START LIGHTING IDIOT THE NOW U JUST BURNT ALL THE TOP-GREEN, YOU FUCKIN' BASTARD!"
(_ //)
From what I read it creates pressure at the top region, creating the bottom region where the stem is to bubble harder, creating extra filtration?!??
What exactly does this machine do anyways?
All I know is it gets me MEGA baked more so than usual...!!!
add-on for most likely any type of bong, with atleast, a decent tube long enough to fit the gadget into the top, the longer the better perculation goes on!!!
Also, be4 I share my neat little gadget, and after you read this post, I'd appreciate if everybody [after you read this of course] reply back, and give me your constructive criticism, and answer me a few things:
- What the hell exactly is this gadget I made called?! Is it a smaller perculator, an add-on perc.?
- If, you made this and tried it out with your bong, did you like how it worked, and was the effect of the smoke better?!
- MOVING ON TO THE POINT OF THIS POINT; CREATING THE ADD-ON GADGET [MAN DO I FEEL LIKE JAMES BOND & MACGUYVER WE'RE GAY 2GETHER, AND ADOPTED ME! LMAO!!!]
Materials:
- Any bong with a long chamber, you know the chamber here lemme explain for the nubs:
| | <--*** PLZ READ: YOUR GONNA STICK THIS INVENTION ABOUT 1 INCH DOWN THE TOP OF THE TUBE!!! ***
| | @ <--Bowl piece (in foreign countries they use 'cones', I prefer the 1 hit bowls.
|o|// <--Stem (Can be slide-out, the o behind the stem inside the bong would be the carb-hole a.k.a. shottie, or "YOUR SUPPOSED TO USE THE SHOTTIE BE4 YOU START LIGHTING IDIOT THE NOW U JUST BURNT ALL THE TOP-GREEN, YOU FUCKIN' BASTARD!"
(_ //)
- A bottle (I used an empty Ginkgo Biloba bottle) YOU MUST USE A WIDE/BIG CAP/NECK OR YOU'LL BE DUCT TAPING THE HELL OUT OF IT TO FIT IN THE TUBE; WE WILL DISCUSS THAT IN THE DIRECTIONS!
- Scissors could work, but I prefer a sharp knife, doesn't matter if sharaded or not.
INSTRUCTIONS:
- I am Not sure if you want to leave the cap on be4 cutting the neck from below the threads down, or take it off and leave it aside; but, you're gonna need the cap and the thread to be able to put the cap back onto the thread for this fadget to work properly. Depending on the bottle you use, you might even be able to cut down more on the bottle, trying to make it fit works better for your self.
- With your knife/scissors, cut the top off leaving the thread.
- Take the knife and poke holes through the top.
- Take your duct tape if necessary and wrap around until it will fit snug into the top of the chamber about one inch down, I made it where the top of the top was showing towards my mouth, now the other way, so it catches filtration at the part wheres theres a lot of plastic for it to catch on.
- Once, inserted one inch into your bong; try dry pulling it. Feel any pressure?!?!
From what I read it creates pressure at the top region, creating the bottom region where the stem is to bubble harder, creating extra filtration?!??
What exactly does this machine do anyways?
All I know is it gets me MEGA baked more so than usual...!!!