Search results

All I know is hydro. Have never done a soil grow. Used to grow ebb and flow on a much larger scale. My current grow is in a micro stealth cabinet, and a small dwc was the only hydro system that would fit/work...but obviously this small system is harder to get dialed in compared to my old E/F...

Appreciate the reply. My temps aren't a problem. Rh is a little low(40%), but am installing a new humidstat this weekend so that shouls be resolved in a few days. Going to start raising nute concentration and see what happens.

Temps are good. Use RO so water should be good.

Usually waited about a week or so...enough time for the next set of leaves to grow in and see that my changes made no difference. Roots were white in sterile(bleach), slight staining from nutes with hydroguard. Never any slime or funky smell. I should note that, aside from my 3part nutes...

No. I empty and fill through a hose fitting.

The peeling paing on my rez looks like shit but it'll work for now. Small/micro DWC. Ph 5.5-6.0. Running AN 3part at 100ppm in RO water. 18-6 lighting. Rez tems 65F. I have no idea whats wrong. Had this same issue with my last grow(same strain). Spent the entire grow trying to figure out...

I'll likely give that a try. I upped the nutes and new growth looks good. Too early to tell if that was the fix since it usually takes a few days for the spots to show. Either way, I'll be switching to bleach in a day or two with the next res change. Thanks!

Thanks! Going to try increasing nutes.

With such a small res, I'm changing every 7-10 days.

Will try upping the ppm to see if it helps. Thanks!

I currently use diluted pool shock. Added every 2-3 days at a rate of 4ppm(based off initial dilution and reservoir capacity) Roots look healthy and white. No slime or funky smells.

Flushed and ran at 0ppm for 2 days, then slowly increases to 100ppm. I'm mainlining so its been topped twice and lollipopped below each top. Same the keeps happening...new growth looks good. Next node grow in, then brown spots start to show on older fan leaves. This is followed by leaf...

Using distilled water. 0ppm.

Greetings....not not sure what I'm up against here. Any advice would be appreciated: Strain- White Widow Small cabinet DWC. 2 weeks into veg. Cal-Mag at 100 ppm, GH 3 part at 200ppm. Ph 5.8 and very stable. 150watt led panel set at 50% Nutrient concentration and light intensity are based on...

Have a dome I can throw over it. Will try that as well.

RH is likely a little low. Usually between 30 and 35% The lower tip burned look is from the low light issue. Now that i look closer. I guess I do see the slight burn on the new growth. I could try lowing the nute strength and see if that helps. Thanks for the reply.

I’m not new to growing in hydro by any means, but I am new to DWC. I took a break for 5 year afters having numerous very successful grows using Ebb and Flow in a 10’x 10’ tent I decided to start experimenting again, this time with small cabinet DWC grow. Not usually one to ask for help as I...

I've been looking at the 4 bulb fixtures but most of them are spec's at over 12" wide. My space is limited to a light no wider than 12. Actually , 12" would have the the light fixture touching the sides of my tent. There are likely ones available that are a bit narrower, I just haven't found...

So, I recently got rid of my large setup and an going back to small hobby growing. my plan now is to keep two small bonsai mother's, my two favorite strains. They will be kept in a 1'x3' area with limited vertical space. I've been looking at smaller T5s( currently use a two bulb , 28w light...

Point well taken and understood. Guess I always thought more light = more yield, which to some extent is true. But I'm more interested in gpw ratio and right now my is pretty shitty. I looked up the splitter and came across the Solis tek one you mentioned. Looks like the pug is the standard...