Search results

  1. Mechmike

    Quantum Board QB 288 V2

    Thanks for the offer but I have modified the sinks so don't really need anything fixed now. Next time I order I will mention that I'd like the sinks that are drilled for the boards I buy. No worries or hard feelings, brother.
  2. Mechmike

    Quantum Board QB 288 V2

    Too late now. I already drilled and tapped the sinks to work for QB288's. If I ever decide to get couple QB324 panels I will have sinks that I can use! I wouldn't like to do the drilling and tapping again. It took about and hour but only because I had the tools handy. If it happens again I...
  3. Mechmike

    Quantum Board QB 288 V2

    The sinks were for the QB324. The QB324 takes 4 screws on each long side and 2 in the middle. The QB288 and QB304 take 3 on the long sides. It was probably a mistake at the packing stage.
  4. Mechmike

    Quantum Board QB 288 V2

    Just to be clear, what I got was 2 boards with 2 single heatsinks. I don't know anything about the double length heatsinks. My guess is that the sinks I got were drilled and tapped for some other configuration. Maybe 304 or 324? There were more mounting holes than are on the QB288's.
  5. Mechmike

    Quantum Board QB 288 V2

    Has anyone received Slate 2 heatsinks that are not drilled for the QB288? I just got a 2 board kit last week that I had to drill and tap holes in the proper places for the QB288's. The only holes that matched up to the boards were the two center ones. That was a bit of a pain. I hope that...
  6. Mechmike

    need help with light

    The other guys are right about the quality of the light. With that said, I can relate to your attempt to make it work. I have some experience fixing the old blurple Epistar lights. My bet is that it's not a driver. Most likely it's a single blue diode that has burnt. The way I have found a...
  7. Mechmike

    Best LED Vegging Setup for 2x4 Tent

    With the Veros you don't need to use the connectors. The chips have big solder pads that work just fine. In fact I like soldering the connections better with 20 guage solid wire. Those little connectors break too easily in my opinion. I run everything in series but I have run them in...
  8. Mechmike

    Best LED Vegging Setup for 2x4 Tent

    I use Vero 18 chips for everything. My veg is specifically designed for a 2x4 veg tent. The light consists of 4" x 36" heatsink with 10 chips. The driver is a Meanwell HLG-120H-C500B. 100k pot for dimming. The driver maxes out at 150w so at full power I am only driving the chips at 15w...
  9. Mechmike

    Can cobs be used as side lighting

    Side lighting with cobs is doable and it works. My lighting has evolved over the years from mostly monos to mostly cobs. I use 3500k Cree CXA1304, 9v version for the side lighting. There are 96 of them in all. I run them at 350ma max with dimmers. Each level is it's own dimmable, switched...
  10. Mechmike

    2x cxa3590 5000k diy veg lamp

    Your driver will work just fine. The Meanwell datasheet shows the overvoltage protection (hiccup mode) activates at 165-175v. You may see a negligible decrease in amperage. It's well below the overvoltage protection at only 6 volts over the driver's 148v spec.
  11. Mechmike

    Heat Sink Shootout: heatsinkusa's 3.945 -vs- 4.6

    I'm interested to see the results of your test. My bet is on the 4.6". The serrations increase the surface area of the fins.
  12. Mechmike

    VERO 13 Powering in Parallel

    You can run Vero13s in parallel. I have a clone light which has 2 vero13 5000k run in parallel off a single Meanwell APC-12-350. The driver outputs 36v which lights up the 2 emitters at 175ma. It uses 11.8 watts at the plug and makes enough light for full tray of cuttings. I can't see any...
  13. Mechmike

    why buy high priced LED for a Name when there all made in china

    Diy is the only way I could buy the quality and configuration I wanted. No question that I got what I paid for. I might buy a commercial led again some day but it will have to be better quality than what I can build.
  14. Mechmike

    Dealing with fan failure

    Well said. My sentiments exactly. Big sinks and just enough fan to keep air moving. Semi-passive design has the advantage of wide margin for fan failure. I actually ran my main overhead light for several days passively but my Veros were getting up to as high as 70c. Cooler is better for...
  15. Mechmike

    Liquid Cooled 8 COB Cabinet

    That should work fine. I would use the pc fans, get and wire in a temperature controller to run the fans only as needed to keep the coolant temperature low. The exhaust fan may work but dedicated cooling is better. Temp controller like this...
  16. Mechmike

    Liquid Cooled 8 COB Cabinet

    Your idea should work great. It will probably never get over 40c. I haven't done it myself but I have pondered how to attach emitters to a water block so they can be replaced without damaging anything. I was thinking that 2" lengths of 2" x .25" aluminum flat strap bonded to the water block...
  17. Mechmike

    Why hole in middle of radial heatsink

    There are some cobs made in the shape of a doughnut, hole and all. I've seen them on Alibaba. Maybe that sink is designed for one of them? It doesn't appear to be much use for the type of cob typically used in grow lighting.
  18. Mechmike

    Best Tool for the Job

    I think your latest light is great! I appreciate seeing what people build, especially the real good ones. Efficiency is no small matter. It's one of the main reasons why I don't use epiwhatever based lights anymore. I just got an email from my power company. My consumption is 9% greater than...
  19. Mechmike

    Best Tool for the Job

    Supra, we think alike. I'm all about big yields in small spaces and with LED it's become a reality for me. I too was an early adopter with led spending way too many dollars per par watt early on. It's been a good learning experience. The way we use LED is as diverse as the people here and...
  20. Mechmike

    ...All Things Vero...

    The internal dimmer on the A version is limited to dimming to about 50%. The pot is accessed through a hole in the top of the driver with a tiny screwdriver. The B version is dimmable for nearly the entire range depending on the potentiometer selected. To dim one driver you'll need a 100k...
Top