havefungodumb
Well-Known Member
THAT would be cool if robots sprayers worked from home depot hehe
Got a question, how high should the water be spraying under the lid of your veg and cloner? Because my sprayers don't reach the net pots. They reach like 2-3 inches below the bottom of my pots. How can my clones root if the water never hits em?
I got that 390+ pump so it's powerfull enough. However I wasn't able to get those Ez-Clone sprayers, instead I got the crappy red 360 ones from home depot, the ones with little tiny holes that clog easy. Are my sprayers the problem? I built it to specifications otherwise.
Also I just have the pump sitting inside the pvc with no seal, is that my pressure problem? How can I seal the pump to the pvc without using cement/silicon?
THAT would be cool if robots sprayers worked from home depot hehe
Either way I'll have to get a special grommet from the eco-plus 396 pump to the 1/2" pvc tube, because I looked in the bottom res of my vegger and saw tons of water pumping out from the bottom pvc connection.
I came here to say something about that. I put together my cloner tonight and can't see any good way to get the pump attached to the 1/2" PVC other than sliding the pipe about 1/4" into the pump, which isn't effective at all. I'm going to have to figure something out... damn. I wanted it up and running tonight!
Also note: PVC cleaner and cement will melt the plastic on the pump case.
lets all smoke to thisI'll smoke to that!
thx!
Thanks Stinkbud, you have helped alot of people and spent tons of time on this thread and I thank you.
Question? Have you tried the garbage bags yet? I guess that you can't put one in the top of the veg unit?
Drain question for veg unit. Has anyone come up with a better idea to put a drain in were you can get it out of the rubbermaid container after you put it in. Thanks again, James
Got a question, how high should the water be spraying under the lid of your veg and cloner? Because my sprayers don't reach the net pots. They reach like 2-3 inches below the bottom of my pots. How can my clones root if the water never hits em?
I got that 390+ pump so it's powerfull enough. However I wasn't able to get those Ez-Clone sprayers, instead I got the crappy red 360 ones from home depot, the ones with little tiny holes that clog easy. Are my sprayers the problem? I built it to specifications otherwise.
Also I just have the pump sitting inside the pvc with no seal, is that my pressure problem? How can I seal the pump to the pvc without using cement/silicon?
Sorry I think we may have mis understood each other
I really just have a small closet / cab style grow which is 5 feet long and 25 inches wide, Can anyone who has built the standard flower system(2 x 4 foot posts and res + framework) tell me if it will fit width wise within 25 inches with enough room for the plants to grow successfully?
Also Stink what is the end cost per pound(not what you sell or distribute it for to your patients)?
lets all smoke to thisthanks stink bud lets see what 12 plants will do under 3 one thousands bulit mine today took me an hour and a couple bong hits
![]()
I came here to say something about that. I put together my cloner tonight and can't see any good way to get the pump attached to the 1/2" PVC other than sliding the pipe about 1/4" into the pump, which isn't effective at all. I'm going to have to figure something out... damn. I wanted it up and running tonight!
Also note: PVC cleaner and cement will melt the plastic on the pump case.
2) One of the plastic fittings has a little nipple with a hole in it. You need to plug that hole or water will come shooting out. Silicone will work, I just stick a wood screw in the hole to plug it up. The 1/2" PVC pipe connects directly to the pump fitting.
That should take care of your problems.