Anybody ever use Rain Rings?

DoubleAtotheRON

Well-Known Member
Im kinda getting tired of hand feeding 24-36 plants every day. I have a tank with recirc, and feed with a shower head wand. My thought was to place 90 of these in my room (30 on each tray) and set up a PVC pipe longways down the middle and about 6 inches above the pots. Drill nipple fittings into the PVC, and run 1/4 hose to each Rain Ring with a 90 degree shut off valve on each one. When those 24 or 43, or 16 need feed, I can just turn on the pump, and open the valves to the ones that need feed. This might save on wasting nutes because we do get a shit ton of runoff, and this would slow the feeding down quite a bit I would think.. Anybody?

Screen Shot 2022-02-05 at 6.57.47 PM.png
 

xtsho

Well-Known Member
I'm surprised none of you guys with larger grows are not using capillary mats.

 

bk78

Well-Known Member

DoubleAtotheRON

Well-Known Member

DoubleAtotheRON

Well-Known Member
I'm surprised none of you guys with larger grows are not using capillary mats.

Only problem with that, is not all of my plants need feeding at the same time, or don't drink at the same rate. Some are 2 day, some 3. Thats why I have anywhere from 20-36 out of 90 to feed every day.
 

DoubleAtotheRON

Well-Known Member
I check every one of them, everyday with a moisture meter, unless I can obviously see that I had feed it the day before. I need to be able to just turn on a valve at each plant.
 

visajoe1

Well-Known Member
Yes, they're great. I use 6" rings in 3g pots. 4x4 tent. Depending on if i have 2 or 4 plants hooked up to rings, it takes 60 or 90 seconds to pump 1g to each pot, with just the right amount of runoff. I fill 3g pots 4" from the top so no overflow when watering, it creates a pool on top that falls through the entire pot. For reference, pump is around 300 gph, plenty of power to push through manifold and shutoffs.

if i scaled my tent model, it would be a presserized system running on a 24hr timer with shutoffs at each table and pot, probably 2g pots to ensure 24hr cycles.
 

DoubleAtotheRON

Well-Known Member
Setup kinda like this....IMG_7525.jpg

I have 3, 20 ft long trays, and I already have almost everything else like trellis, frame, I could just run that 1 in PVC right down the middle of each tray. IDK... just working this out in my head.
 

DoubleAtotheRON

Well-Known Member
Most definitely you do, but the trick is to keep the proper pressure so the feeds are the same for each site?
That's the big question!.. I think if the 1inch PVC that will be hung down the middle is not "pressurized" so to speak, but "full", then they should gravity feed at the same rate. I may just build a setup on one tray and experiment with it. I can regulate pressure at my mix tank. Maybe put it at like 1-2 PSI.. IDK... I'll post results! I need to break out the laser level anyways. Im going to try to get the PVC feed pipe as level as possible.
 

bk78

Well-Known Member
That's the big question!.. I think if the 1inch PVC that will be hung down the middle is not "pressurized" so to speak, but "full", then they should gravity feed at the same rate. I may just build a setup on one tray and experiment with it. I can regulate pressure at my mix tank. Maybe put it at like 1-2 PSI.. IDK... I'll post results! I need to break out the laser level anyways. Im going to try to get the PVC feed pipe as level as possible.

Following along for the ride most definitely
 

DoubleAtotheRON

Well-Known Member
Ideally, I want the ring to just drip at a decent rate and not spray. That way I can just open valves, go do some other shit, and then once they are saturated, move the hose to the next tray via the quick connect.
 
Top